Operation; General - Hatco IWRM-UT Série Manuel D'installation Et D'utilisation

English

General

Use the following information and procedures to operate an
Under-Counter Induction Warmer.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
BURN HAZARD:
• Do not leave metal objects or utensils on or near trivet/
induction warmer. They may become hot.
• Use caution when wearing rings, watches, or other
ferrous objects around trivet/induction warmer. They
may become hot.
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
Pan Specifications
Pans used with an Induction Warmer must meet the following
specifications:
• Made of material with magnetic properties (ferrous material)
- Enameled Steel Pans
- Cast Iron Pans
- Stainless Steel Pans
- Aluminum Pans w/ferrous base
• Proper size (measurements given are the pan bottom
diameter)
- Minimum = 5" (127 mm), Maximum = 13" (330 mm)
• Flat bottom
The following pans cannot be used with an Induction Warmer:
• Glass Pans
• Aluminum Pans without a ferrous base
• Earthenware Pans
• Ceramic Pans
• Copper Pans
• Non-Ferrous Stainless Steel Pans
NOTE: The Induction Warmer automatically detects if a pan is
induction-ready. If a pan is placed on the trivet during
operation that is not induction-ready, the LED display
will read "ADD PAN", and the unit will not operate.
Preheat Button
On/Off Button
Trivet Centering
Indicator
Model IWRM-UT-06 Control Panel
Form No. IWRMUM-0321
CAUTION
Power Control
Arrow Buttons
Control Lock
Button
Startup
1. Make sure the unit is plugged into a properly grounded
electrical receptacle of the correct voltage, size, and plug
configuration. See the SPECIFICATIONS section for
details.
2. If this is the first time the unit will be used after installation,
perform the "Calibrating the Trivet" procedure in the
INSTALLATION section. NOTICE: Trivet must be
calibrated to unit before first use.
• Skip steps 3 and 4 of this procedure after calibrating the
trivet. The unit will be on and the trivet will be centered
already.
3. Press the
• The green indicator on the
• At first startup, and anytime the trivet is missing, the LED
display will read "NO TRIVET". The unit will beep slowly.
NOTE: The unit can be turned off at any time by pressing the
button.
4. If the trivet is not present, center the trivet on the countertop.
NOTE: Do not place a pan on the trivet during the centering
process. The unit may not operate properly.
a. Slide the trivet slowly on the countertop toward the
center of the Induction Warmer installed underneath
countertop. The unit will begin beeping.
• The LED display will show numbers between 1 and
4, and the green Trivet Centering indicator will begin
blinking slowly.
• As the trivet gets closer to the center, the beep will
increase in frequency, the number will increase, and
the Trivet Centering indicator will blink faster.
b. Keep moving the trivet until the LED display shows the
number 4, a long beep sounds, and the Trivet Centering
indicator stays solid green. The LED display will change
to "ADD PAN".
NOTE: If the unit is turned off by pressing the
the trivet is not moved, the unit can be turned on and
used without re-centering the trivet. If the trivet is moved
and/or the unit is unplugged, the trivet will need to be
centered again.
5. If warming with a chafing dish:
a. Fill an induction-ready chafing pan with warm water to a
depth of approximately 1/2" (12 mm) .
b. Place the pan on the trivet.
LED
c. Press the
Display
button will illuminate, and the LED display will show the
remaining minutes of preheat mode ("60M").
d. Allow the unit to preheat for approximately 40–60 minutes.
The unit will switch automatically to normal operation
when preheating is done. The unit will operate at the
same power setting from when it was last shut down.
NOTE: To prevent overheating, the unit software will allow only
three preheating modes during a 24-hour period. If the
unit is off for over five hours, the 24-hour period restarts.
e. Place the chafing dish with preheated food product into
the chafing pan.
f. Continue to monitor the water level in the chafing pan.
NOTE: To exit preheat mode manually, press either the
,or
9

OPERATION

button to turn on the unit.
button will illuminate.
button. The red indicator on the
button.
button and
,
continued...