Publicité
Les langues disponibles
Les langues disponibles
Putting into operation
u Slide up the assembly aids
unit door. Lower stop edge ▲of the assembly aid = upper
edge of the unit door to be fitted.
u Unscrew the cross-
Fig. 19 (31)
piece
by undoing the lock-
Fig. 19 (32) .
nuts
u Attach the cross-
Fig. 19 (31)
piece
together with the
assembly
aids
Fig. 19 (30) to the
inside of the unit
door.
For 600 mm-wide recess:
u Concentrically align the crosspiece
short centre line on the unit door and put the tip of the arrow
on the crosspiece over it.
w Distances to the outer edge are equal at the left and right.
For particle board doors:
u Tightly screw the crosspiece
Fig. 19 (41) .
least 6 screws
For frame and panel doors:
u Tightly screw the crosspiece
Fig. 19 (41) at the edge.
screws
u Raise and remove the assembly aids
and slide them into the adjacent openings.
Fig. 20
u Attach the unit door to the adjusting bolts
loosely screw the locknuts
bolts.
u Close the door.
u Check the gap between the door and the surrounding unit
doors.
u To laterally align the unit door: Move the unit door in the X
direction.
u Align unit door in height and lateral inclination: Adjust the
Fig. 20 (33) using a screwdriver.
adjusting bolts
w The unit door is flush and in alignment with the surrounding
unit fronts.
u Tighten the lock nuts
Fig. 20 (32) .
Ensure that both metal
edges
are
flush
(symbol //):
u Drill pilot holes in the
door
of
the
unit
(possibly
make
preliminary hole with a
bradawl).
u Screw the appliance door to the unit door with screws
Fig. 21 (41) passed through the mounting brackets
Fig. 21 (34) .
38
Fig. 18 (30) to the height of the
Fig. 19
Fig. 19 (31) : Mark a
Fig. 19 (31) into place using at
Fig. 19 (31) into place using 4
Fig. 19 (30) , turn them
Fig. 20 (33) and
Fig. 20 (32) onto the adjusting
Fig. 21
Fig. 22
u To align the unit door in depth Z: Undo top screws
Fig. 22 (36) , bottom hexagon head screws Fig. 22 (35) with
Fig. 22 (37) provided, then shift the door.
ring spanner
u Do not allow the knobs and sealing lips
to abut - vital for proper function!
u Allow an air gap of 2 mm between the
unit door and the body of the unit.
For large unit doors:
u fit
a
3rd
pair
of
Fig. 9 (34) .
u Use the holes pre-drilled in the handle area
of the appliance door for this purpose.
u Check the fit
of the door
and adjust if
necessary.
u Tighten
all
screws.
Fig. 23 (32) using the ring spanner
u Tighten the locknuts
Fig. 23 (37) , while holding fast the adjusting bolts
Fig. 23 (33) with a screwdriver.
u Put on and engage the
upper
covers
Fig. 24 (38) .
u Place
lateral
covers
Fig. 24 (39) in position,
slide them to the limit,
then press, until you
hear them snap into
place.
u Attach
covers
Fig. 24 (40) sideways
and then draw them
forwards with a screw-
driver so that they snap
into place.
u Put on and engage the covers
mounting
brackets
Fig. 6 (5,6,7) .
Fig. 23
Fig. 24
Publicité
