Publicité
Les langues disponibles
Les langues disponibles
• When operating a power tool outdoors, use an extension
cord suitable for outdoor use . Use of a cord suitable for
outdoor use reduces the risk of electric shock .
• If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected sup-
ply . Use of an RCD reduces the risk of electric shock .
Personal safety
• Stay alert, watch what you are doing and use common
sense when operating a power tool . Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication . A moment of inattention while
operating power tools may result in serious personal
injury .
• Use personal protective equipment . Always wear eye
protection . Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries .
• Prevent unintentional starting . Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool . Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents .
• Remove any adjusting key or wrench before turning the
power tool on . A wrench or a key left attached to a rotat-
ing part of the power tool may result in personal injury .
• Do not overreach . Keep proper footing and balance at
all times . This enables better control of the power tool in
unexpected situations .
• Dress properly . Do not wear loose clothing or jewellery .
Keep your hair, clothing and gloves away from mov-
ing parts . Loose clothes, jewellery or long hair can be
caught in moving parts .
• If devices are provided for the connection of dust extrac-
tion and collection facilities, ensure these are connected
and properly used . Use of dust collection can reduce
dust-related hazards .
Power tool use and care
• Do not force the power tool . Use the correct power
tool for your application . The correct power tool will
do the job better and safer at the rate for which it was
designed .
• Do not use the power tool if the switch does not turn
it on and off . Any power tool that cannot be controlled
with the switch is dangerous and must be repaired .
• Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools . Such preventive safety measures reduce the risk of
starting the power tool accidentally .
• Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool . Power
tools are dangerous in the hands of untrained users .
• Maintain power tools . Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation . If
damaged, have the power tool repaired before use . Many
accidents are caused by poorly maintained power tools .
• Keep cutting tools sharp and clean . Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control .
• Use the power tool, accessories and tool bits etc . in
accordance with these instructions, taking into account
the working conditions and the work to be performed .
Use of the power tool for operations different from
those intended could result in a hazardous situation .
Service
Have your power tool serviced by a qualified repair person
using only identical replacement parts . This will ensure
that the safety of the power tool is maintained .
SAFETY WARNINGS FOR POLISHERS
• This power tool is intended to function as a sander, wire
brush and polisher . Read all safety warnings, instruc-
tions, illustrations and specifications provided with
this power tool . Failure the follow all instructions listed
below may result in electric shock, fire and/or serious
injury .
• Operations such as grinding or cutting-off are not rec-
ommended to be performed with this power tool . Op-
erations for which the power tool was not designed may
create a hazard and cause personal injury .
• Do not use accessories which are not specifically de-
signed and recommended by the tool manufacturer .
Just because the accessory can be attached to your
power tool, it does not assure safe operation .
• The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool .
Accessories running faster than their rated speed can
break and fly apart .
• The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool . Incorrectly sized accessories cannot be adequately
guarded or controlled .
• Threaded mounting of accessories must match the
grinder spindle thread . For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange . Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss
of control .
• Do not use a damaged accessory . Before each use in-
spect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires . If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory . After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute . Dam-
aged accessories will normally break apart during this
test time .
• Wear personal protective equipment . Depending on
application, use face shield, safety goggles or safety
glasses . As appropriate, wear dust mask, hearing protec-
tors, gloves and shop apron capable of stopping small
abrasive or workpiece fragments . The eye protection
must be capable of stopping flying debris generated by
various operations . The dust mask or respirator must be
capable of filtrating particles generated by your opera-
8
Publicité
