T.I.P. HWW INOX 1000 Plus Mode D'emploi page 18

MALFUNCTION
4. The pump cuts in and out too
frequently.
5. The pump does not reach the desired
pressure.
6. The pump does not cut out.
12. Warranty
The present device was manufactured and inspected according to the latest methods. The seller warrants for
faultless material and workmanship in accordance with the legal regulations of the country in which the device
was purchased. The warranty period begins with the day of the purchase and is subject to the provisions below:
Within the period of warranty, all defects which are to be attributable to defective materials or manufacturing will
be eliminated free of charge. Any complaints are to be reported immediately upon their detection.
The warranty claim becomes void in the case of interventions undertaken by the purchaser or by third parties.
Damage resulting from improper handling or operation, incorrect setting-up or storage, inappropriate connection
or installation or Acts of God or other external influences are excluded from warranty.
Parts being subject to wear and tear, such as the pump wheel (impeller), mechanical shaft seals, membranes and
pressure switch are excluded from warranty. All parts were manufactured using maximum care and high-quality
materials and are designed for a long lifecycle. It should be understood, however, that the wear and tear depends
on the kind of use, the intensity of use and the internals of maintenance. Complying with the installation and
maintenance information contained in the present operating instructions will therefore considerably contribute to a
long lifecycle of these wearing parts. In case of complaints, we reserve the option of repairing or replacing the
defective parts or replace the entire device. Replaced parts will pass into our property.
Claims for liquidated damages are excluded unless they are caused by wilful acts or negligence on the side of the
manufacturer.
The warranty does not provide for any claims beyond those referred to above. The warranty claim has to be
evidenced by the purchaser in the form of the submission of the sales receipt. The present warranty commitment
is valid in the country in which the device was purchased.
Please note:
1. Should your device fail to function properly, please verify first whether an operating error or another cause is
present which cannot be attributed to a defect of the device.
2. In case you have to take or send in your defective device for repair, please be sure to enclose the following
documents:
a. Sales receipt (sales slip).
b. A description of the occurring defect (a description as accurate as possible will expedite the repair
work).
3. In case you have to take or send in your defective device for repair, please remove any attached parts which
do not belong to the original condition of the device. If any attached parts of this kind should be missing upon
the return of the device, we shall not be liable for them.
13. How to order spare parts
The fastest, most simple and cheapest way of ordering spare parts is through the internet. On our
www.tip-pumpen.de website you will find a convenient spare part shop where you can order spare parts with just
a couple of clicks. In addition, this is also the place where we publish comprehensive information and valuable
tips on our products and accessories, introduce new devices and present current trends and innovations in the
range of pump technology.
14. Service
In the case of warranty claims or malfunction, please contact your point of sale.
A current operating manual is available as required as a PDF file via e-mail: service@tip-pumpen.de.
For EC countries only
Do not throw electric appliances in your dustbin!
According to EU guideline 2012/19/EU concerning old electric and electronic appliances and its
implementation in national law, such appliances must be collected separately and fed into an
environment-friendly recycling system. Please consult your local waste management system for
advice on recycling.
15
POSSIBLE CAUSE
1. The membrane of the pressure tank is damaged.
2. Insufficient pressure in the pressure tank.
3. Air penetrates into the intake line.
4. Check valve (non-return valve) is jammed or not
tight .
1. Cut-out pressure set too low.
2. Air penetrates into the intake line.
1. Cut out pressure set too high.
2. Air penetrates into the intake line.
1. Have the membrane or the entire pressure tank
replaced by qualified staff.
2. Use the tank valve to increase the pressure until it
reaches a value of 1.5 bar. Before that, please open a
consumer in the pressure line (e.g. a faucet) to
depressurise the system.
3. Refer to section 2.2.
4. Eliminate the cause of blocking the check valve
(non-return valve) or replace it if damaged.
1. Please contact the customer service department.
2. Refer to section 2.2.
1. Please contact the customer service department.
2. Refer to section 2.2.
7
ELIMINATION