Publicité
Les langues disponibles
Les langues disponibles
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press START/RESUME, the dishwasher
runs the last full
wash cycle and options.
Hi Temp Wash
Select this option to heat the water to 140°F (60°C) during parts
of the cycle. Heating the water helps improve washing results.
This option adds heat, water and wash time to parts of the cycle.
Hi Temp Wash is useful when loads contain tough food soil items.
NOTES:
•
Pots Pans automatically
uses this option. Hi Temp Wash is an
option with the Heavy Wash and Normal Wash cycles.
•
Use this option for heavier than normal-soiled
loads.
Sani Rinse
Select this option to raise the water temperature
in the final rinse
to approximately
155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high-temperature
rinse sanitizes your dishes and
glassware in accordance with the NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers
are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with Pots Pans, Heavy Wash and
Normal Wash. Only these sanitization cycles have been designed
to meet the NSF/ANSI requirements.
Heated Dry
The Heated Dry option in combination
with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dishload that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick
Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher.
You can also use the lock feature to prevent unintended cycle or
option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher
is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, firmly close the door until it latches and
press START/RESUME, or the delay will not continue.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3.
Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
•
To cancel the delay and cycle, press CANCEL/DRAIN.
•
To cancel the delay and star[ the cycle, press START/
RESUME.
Follow the progress of your dishwasher with the Cycle Status
indicators.
WASHING
SENSING
DRYING
SANITIZED
CLEAN
NOTE: The features on your dishwasher
may vary from those
shown here.
Sensing
Your dishwasher senses the soil level on the dishes. Soil level
determines the length of some cycles, the amount of heat added
to the wash or rinse, and the cycle needed for the load. SENSING
glows during the soil sensing parts of the cycle. Wash action
continues while sensing occurs.
Sanitized
If you select the Sani Rinse option, Sanitized glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted
or the incoming water
temperature
is too low. The light turns off when you press any
button or close the door.
Clean
Clean glows when a cycle is finished. The light turns off when you
press any button or close the door.
During drying, you can see steam escaping through the vent at
the upper left corner of the door. This is normal as the heat dries
your dishes.
#1 t
•
%_,
IMPORTANT: The vapor is hot, Do net touch the vent
during drying.
13
Publicité
