Publicité
Les langues disponibles
Les langues disponibles
CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
Excessive torque may cause breakage and possible
personal injury.
Cat #
DCF510
1. Install the appropriate anvil
a. If an anvil is installed on the tool, push the release
button
9
on the backside of the tool and remove
the anvil.
b. To install an anvil, push the desired anvil into the tool
until it is secure.
2. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
3. Consider the intended operation and select either
forward or reverse rotation.
4. Press variable speed trigger switch
5. Release variable speed trigger switch
6. If the ratchet stalls, the tool is overloaded or is being
improperly used. Release the variable speed trigger
switch
immediately. Do not press the variable speed
1
trigger switch
on and off in an attempt to start a
1
stalled ratchet. Doing so can damage the tool.
7. The ratchet can also be used manually for breaking free
stubborn fasteners or snugging by releasing the trigger
and applying the torque by hand.
nOTE: Excessive manually applied torque may damage
the anvil if it exceeds the torque limit 175 ft.lbs.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
RPM
Ft.‑lbs.
0–300
75 (Max.)
101.69 (Max.)
2
(3/8" or 1/2") on the tool.
to start operation.
1
1
to stop operation.
Accessories
WARNING: Since accessories, other than those
offered by D
product, use of such accessories with this tool could be
nm
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website:www.dewalt.com.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
• Register online at www.dewalt.com
Three Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/Legal/
Warranty/3‑Year‑Limited‑Warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
WALT, have not been tested with this
e
WALT call 1‑800‑4‑D
e
WALT factory service center or a
e
WALT Industrial Tool Co., 701 East
e
English
WALT
e
WALT
e
WALT
e
WALT
e
9
Publicité
