Publicité
Les langues disponibles
Les langues disponibles
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it
from being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off
and then on again. If the machine does not start up again,
the battery pack may have discharged completely. In this
case it must be recharged in the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
REPLACING CUTTING LINE
Use only MILWAUKEE trimmer line (see technical data).
Replace the cutting line with either 6 m of 2,4 mm line or 7,6
m of 2 mm line. Note, when used near abrasive surfaces or
in dense growth, the cutting line will wear faster.
For replacing cutting line see picture section.
Under normal operation, the remaining string should be
thrown from the spinning head during use. If any string
remains in the head, or to remove a length of string to
replace with a diff erent type, turn the trimmer head over and
press the release tabs and pull the cover away from the
head.
24
ENGLISH
Discard any short line remnants. Snap the cover back onto
the trimmer head.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Servicing requires extreme care and knowledge and should
be performed only by a qualifi ed service technician. For
service, we suggest you return the product to your nearest
authorised service center for repair. When servicing, use
only identical replacement parts.
Switch off and remove battery pack before conducting any
maintenance or cleaning work.
You may make adjustments and repairs described here. For
other repairs, contact the authorised service agent.
For replacement line, use only nylon fi lament line of the
diameter described in the specifi cation table of this manual.
After extending new cutter line, always return the product to
its normal operating position before starting.
After each use, clean the product with a soft dry cloth. Any
part that is damaged should be properly repaired or
replaced by an authorised service centre.
Check all nuts, bolts, and screws at frequent intervals for
proper tightness to ensure the product is in safe working
condition.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Please read the instructions carefully before
starting the machine.
Remove the battery pack before starting any
work on the machine.
Wear gloves!
Wear ear protectors!
Always wear goggles when using the machine.
Always wear protective clothing and footwear
Keep bystanders a safe distance away from the
machine.
Do not use in the rain or leave outdoors while it is
raining.
Beware of thrown or fl ying objects. Keep all
bystanders a safe distance away from the
product.
Do not use metal blade(s) on the product.
Rotation direction
Parts or accessories sold separately.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
Britisches Konformitätszeichen
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
25
Publicité
