Manuels Connexes pour Star Ultra Max UM1850A
Sommaire des Matières pour Star Ultra Max UM1850A
- Page 1 ® ELECTRIC CONVEYOR OVEN MODEL UM1833A UM1850A Installation and Operation Instructions 2M-Z9844 Rev. G 02/2018 UM1850A 230 V models only...
- Page 2 Star’s discretion or water connection. Star is not liable for any unit which has have the parts replaced or repaired by Star or a Star-authorized service been mishandled, abused, misapplied, subjected to chlorides, harsh agency.
- Page 3 RETAIN THIS MANUAL FOR FUTURE REFERENCE NOTICE Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability. Star reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
- Page 4 SPECIFICATIONS UM1833A-208V, UM1833A-240V Rating/Connection: 6,400 Watts (6,000 element), 32/29 Amps at 208/240V NEMA 6-50 plus with six foot oil-resistant cord Electrical Supply: Separate 50 Amp 208/240VAC, single phase, 50/60 Hz service per Oven Approximate Weight: 1833 Oven with Legs): Installed - 180 Lbs (81.8 kg),...
- Page 5 SPECIFICATIONS UM1833 WITH INFEED/EXIT SHELVES 24.1 [612] TOP VIEW 1833 W\OUT SHELVES SHOWN A = 51.2 (1300) A1= 50.0 (1270) A2= 33.0 (838) STACKED DIMENSION B = 30.4 (772) CONTROL BOX = C + C1 C = 16.0 (406) DOOR OPEN [208] C1= 20.0 (508) UM1850...
- Page 6 GENERAL INFORMATION This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations. First and foremost, each crate should be examined before signing the Bill of Lading to report any visible damage by the trucker in transit and to account for the proper number of crates.
- Page 7 Do not attempt to operate the oven until connection of utility service has been fully inspected by an authorized service technician or a Star Service Representative. This service is required by Star in order to assist the purchaser in proper start-up of the oven on site. Please note the specific details on the Warranty and make certain that service connections are made to proper utility services.
- Page 8 This appliance must be installed on a sturdy counter or stand using the feet provided for cleaning clearance. As a minimum, 24" of clearance on the discharge end of the oven should be allowed for removal of the conveyor assembly if the oven is not on a mobile cart.
- Page 9 DO NOT ATTEMPT TO OPERATE THE OVEN until connection of utility service and installation has been fully inspected (start-up check- out) by an authorized service technician or a Star Service Technician in order to assure the oven is properly installed and in working order.
- Page 10 Please take time to read the following safety operating instructions. They are the key to the successful operation of your Ultra-Max Conveyor Oven. General Safety Tips: SAFETY TIPS 1. If the oven needs to be moved for any reason, the power must be disconnected from the unit For your safety, read before operating.
- Page 11 DISPLAY INFORMATION When operating the oven, there are three levels of access: 1. Store Level - General employees would know these functions and how to change them. While the oven is running, enter this mode by holding the DOWN and UP arrows ( ) simultaneously for four seconds.
- Page 12 BAKE TIME VERSUS TEMPERATURE 1. Bake time is actually conveyor speed and is defined as the time the product is actually in the oven. This is measured by noting the time when the leading edge of the product enters the oven and the time the leading edge of the product leaves the oven.
- Page 13 EVERY TWELVE MONTHS A factory authorized service person should: 1. Open and clean the inside of the control box. 2. Check and tighten all electrical components. If maintenance is required, contact your local service company, a factory representative, or Star Manufacturing.
- Page 14 Removing Finger Assemblies 1. Once cooled, REMOVE conveyor assembly and door. 2. Life up and remove Upper & Lower Baffles as shown in Step 1. 3. Slide Finger Assembly out of unit as shown in Step 2. 4. Lift Assembly apart as shown in Step 3. and wash in a hot water, detergent mix and rinse with clean water.
- Page 15 CONVEYOR BELT TENSION The conveyor belt of the Ultra-Max Conveyor Oven does not have a tension adjustment. If the belt becomes too loose, a link will have to be removed to tighten. A belt that is too tight will also cause operational problems due to excessive drag.
- Page 16 BLACK WIRE FROM MOTOR GOES TO "W" CONNECTOR ON BOARD GOES TO 'V" CONNECTOR ON BOARD � CUSTOMER RESPONSIBLE FOR FINAL STAR MANUFACTURING INTERNATIONAL, INC. INSTALLATION PER LOCAL CODES. DEDICATED 10 50A CIRCUIT REQUIRED. MODEL: UME 208-240/10 2M-Z13287 REV B 1/31/2018 DR: JT...
- Page 17 GOES TO "W" CONNECTOR ON BOARD GOES TO "V" CONNECTOR ON BOARD � CUSTOMER RESPONSIBLE FOR FINAL INSTALLATION PER LOCAL CODES. STAR MANUFACTURING INTERNATIONAL, INC. DEDICATED 30 20A CIRCUIT REQUIRED. CORD OR CONDUIT CONNECTED AS 2M-Z13288 01-31-2018 DR: JT MODEL: UME 230/30...
- Page 18 31}-------------------, �o "---i �----1(M ::::0 �M ::ti :;:o )> �B -240v 208-24 2cJ I+ 0 �fTl 208-240v ..-1'-C � s:::: -----1(GRN) � (/) )> � � � • ..• :;:o - CAPACITOR, CIRC FAN MOTOR ::::0 8 :1:: �...
- Page 23 PARTS LIST March 26, 2013, Rev. E Ultra-Max Electric Conveyor Oven UM1833A/1850A-208/240V - Main Assembly MODEL Number Part Unit Number Number Description and Model Designation G9-Z5716 TUNNEL SHROUD G9-Z5745 INFEED SHELF G9-Z5362 EXIT SHELF 2A-Z0314 ADJUSTABLE LEG 2C-Z5182 THUMB SCREW 2M-Z20166 CONTROL GRAPHIC 2M-Z5665...
- Page 24 REAR PANEL WELDMENT, QUAD UM1833A, UM1850A IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Star Manufacturing International, Inc.
- Page 25 SOME ITEMS ARE INCLUDED FOR ILLUSTRATIVE PURPOSES ONLY AND IN CERTAIN INSTANCES MAY NOT BE AVAILABLE MODEL: UM1833A & UM1850A CONVEYOR OVEN CONTROL BOX SK2484 Rev. A 1/10/2013 AC MOTOR CONFIGURATION...
- Page 26 PARTS LIST September 16, 2015, Rev. F Ultra-Max Electric Conveyor Oven UM1833A/1850A-208/240V - Control Box , AC Motor MODEL Manufactured After 10/2010 Number Part Number Unit Description and Model Designation Number 2E-Z1858 SWITCH-LIGHTED 2K-Z1971 SPACER .257X.75X.25 NYLON 2C-200201 NUT 6-32 HEX LOCK SS PS-Z7718 KIT,OVEN CNTRL-PRGM+REPLMNT 2C-200014...
- Page 28 PARTS LIST March 26, 2013, Rev. E Ultra-Max Electric Conveyor Oven UM1833A/1850A-208/240V - Control Box , DC Motor MODEL Manufactured Before 10/2010 Number Part Description Number Number Unit 2E-Z5798 CORD SET 208V, 50A 1 Phase G9-EC0014 CONTROL BOX DOOR ASSEMBLY PS-Z7718 CONTROLLER, TIME / TEMPERATURE 2E-Z5683...
- Page 29 2E-Z5681 FUSEHOLDER 2C-Z3350 HALF CLAMP IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Star Manufacturing International, Inc.
- Page 31 FINGER WELD, LOWER - QUAD IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Star Manufacturing International, Inc.