Télécharger Imprimer la page

Makita SC130DRA Manuel D'instructions page 9

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
(Fig. 4 for SC161DW and SC190DW)
1.
Plug the battery charger into your power source. The charging light will flash in green color.
2.
Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as
their respective markings on the battery charger. Insert the cartridge fully into the port so that it rests on the
charger port floor.
3.
When the battery cartridge is inserted, the charging light color will change from green to red and charging will
begin. The charging light will keep lighting up steadily during charging.
4.
When charging is completed, the charging light color will change from red to green.
5.
After charging, unplug the charger from the power source. The charging time is as follows:
Battery type
1822
1833
1834
1835
CAUTION for SC130DRA:
• The fast charger Model DC1439 is for charging Makita battery cartridge. Never use it for other purposes or for other
manufacturer's batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it
may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-
tery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location
exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a
while. Charging will begin after the battery cartridge cools.
• If the charging light flashes alternately in green and red color and tone will sound "beep, beep, beep, ...." for about 20
seconds, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are
clogged with dust or the battery cartridge is worn out or damaged.
• If charging two or more battery cartridges in succession with fast charger DC1439, the charging time may become
longer to protect the charger.
CAUTION for SC161DW and SC190DW:
• The battery charger Model DC1803 is for charging Makita-battery cartridge. Never use it for other purposes or for
other manufacturer's batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it
may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-
tery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location
exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a
while. Charging will begin after the battery cartridge cools.
• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger
or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.
• If you wish to charge two battery cartridge, allow 15 minutes between chargings on the battery charger.
• Any of the following conditions indicates damage to the charger and/or battery cartridge. Ask your Makita Authorized
or Factory Service Center to check them.
1) The charging light does not flash (green) when the battery charger is plugged into a power source.
2) The charging light does not light up or flash (red) when the battery is inserted in the charger port.
3) Charging is not completed at even more than two hours after red light comes ON at start of charging.
Installing or removing cutters
(Fig. 5 for SC130DRA, Fig. 6 for SC161DW and Fig. 7 for SC190DW)
CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or remov-
ing the cutters.
Capacity (mAh)
2,000
2,200
2,600
3,000
Number of cells
15
15
15
15
Charging time
Approx. 45 min.
Approx. 50 min.
Approx. 60 min.
Approx. 70 min.
9

Publicité

loading

Ce manuel est également adapté pour:

Sc161dwSc190dw