All manuals and user guides at all-guides.com
TM
AQUASMART
WATER SOFTENER
WARRANTY
FULL PARTS WARRANTY ON AQUASMART
™ WATER SOFTENER UNIT
(EXCEPT SALT AND CONSUMABLES) YOU
MUST KEEP YOUR WATER2BUY ™
RECEIPT AS PROOF OF PURCHASE.
WARRANTIES ARE 1 YEAR FROM DATE OF
PURCHASE BY DEFAULT.
YOU MAY EXTEND YOUR WARRENY TO 7
YEARS NOW BY COMPLETING YOUR
EXTENDED WARRENTY FORM ON.
WWW.WATER2BUY.COM/WARRENTY
EXTENDED WARRENTIES MUST BE
CLAIMED WITHIN 1 MONTH OF PURCHASE
DATE.
Where the AquaSmart ™ water softener is
installed and maintained in accordance with
these instructions, Water2buy ™ will replace,
free of charge, defects in product parts.
Warranty excludes salt, any other consumables
and labour. This warranty only applies while unit
is in use in the European union.
WATER2BUY ™ INSTALLATION POLICY
All installation should be performed in a neat,
professional manner in accordance with
generally accepted trade practices. Further, all
installations shall comply with all local laws,
codes, regulations, and ordinances. This
manual should be used as a guide only.
BEFORE YOU BEGIN TO INSTALL YOUR AQUASMART
DO
Turn off water mains and release pressure
•
by turning on cold tap
Locate mains water pipe this is usually
located under the kitchen sink or in the
pump house if you have a well supply.
Use the correct tools. Adjustable wrench,
•
standard pliers, and larger adjustable jaw
pliers or pipe wrench to fit sink drain slotted
and Phillips head screwdrivers, pipe joint
compound (thread seal) or Teflon tape,
approved for use on potable water supplies,
hand or battery powered drill.
Select a location. Decide on a position
•
where you want to locate your water
softener. The most common areas are:
SAFETY GUIDES
Read all steps, guides and rules carefully before installing
and using your water softener. Follow all steps exactly to
correctly install. Reading this manual will help you get all
the benefits from your AquaSmart ™ water softener. We
recommend that a trained professional install this water
softener.
Please follow all local codes for plumbing this unit.
Follow local electrical codes. Install a correctly sized
electrical bonding jumper between the inlet and outlet
pipes when these devices are installed in metallic plumbing
systems.
Inspect this unit carefully for carrier shortage or shipping
damage before beginning installation of unit.
This system should not be used for treating water that is
microbiologically unsafe or of unknown quality. The unit is
designed with the sole purpose of removing hardness.
Use only lead-free solder and flux, as required by country
and local codes, when installing soldered copper plumbing.
Use caution when 'sweat joining' metal pipes near this
water conditioning system. Heat can adversely affect the
plastic used in this system and bypass valve.
Use only silicone grease for lubrication of this unit.
Do not allow this water softener to freeze. Damage from
freezing will void this water softener's warranty. Do not
store flammable or volatile chemicals near this water
softener.
For the purpose of plumbing system sizing, only the rated
service (i.e."Normal") flow and corresponding pressure loss
may be used. The rated service flow rates are the flow
rates
TM
WATER SOFTENER
DO NOT
Water heaters. Use at least 3 metres of tubing
•
between the outlet of the water softener and the inlet
to the water heater. Water heaters can overheat to the
extent that they can send heat back down the cold
pipe into the unit control valve.
Hot Water. Hot water can severely damage the
•
softener. A 3-metre total pipe run, including bends,
elbows, and fittings, is a reasonable distance to help
hot water damage. A positive way to prevent hot water
from flowing from heat source to the water softener, in
the event of a negative pressure situation, is to install a
check valve in the soft water tubing from the softener.
If a check valve is installed, make sure the water-
heating unit is equipped with a rated temperature and
pressure safety relief valve. Be sure that local codes
are not violated.
Water2buy.com Aquasmart™ v3
3 / 53