Bosch PowerPack 300 Notice Originale page 32

English–6
Speed and Distance Indication
The speed indication f always displays the current speed.
The following functions are available in the function indica-
tion (combination of text indication d and value indication e):
– "Clock": Current time
– "Max. speed": Maximum speed achieved since the last
reset
– "Avg. speed": Average speed achieved since the last reset
– "Trip time": Trip time since the last reset
– "Range": Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
– "Odometer": Display of the total distance travelled with
the eBike (cannot be reset)
– " NuVinci Cadence/Gear": This menu item is displayed
only in conjunction with a Nu Vinci H|Sync automatic trans-
mission.
If you press the "i" button for longer than 1 s, you will ac-
cess the NuVinci menu item from any menu item in the in-
formation menu.
To switch from the " NuVinci Cadence" mode to the
" NuVinci Gear" mode, press the "i" button for 1 s.
To switch from the " NuVinci Gear" mode to the
" NuVinci Cadence" mode, all you have to do is briefly
press the "i" button.
The default setting is " NuVinci Cadence".
Range
– "Gear": This menu item appears only in conjunction with a
Shimano Di2 gear hub. The currently engaged gear of the
transmission is shown on the display. The newly engaged
gear will be shown briefly on the display whenever the gear
is shifted.
– " Gear: Auto": This menu item appears only in conjunc-
tion with an SRAM automatic transmission.
Range
By pressing the "i" button for more than 1 s, you can
switch back and forth between the " Gear: Auto" auto-
matic mode and the " Gear" manual mode.
If you are in first gear in manual mode, you can also press
the "–" 12 button to go to the " Gear: Auto" mode. By
pressing the "–" 12 button again, you can switch back to
0 276 001 SPI | (3.6.15)
Odometer NuVinci Cadence
(1 s)
(1 s)
NuVinci Gear
Odometer Gear: Auto
(1 s)
(1 s)
Gear
the manual mode. It is also possible to access the manual
mode by pressing the "+" 13 button.
– "Trip distance": Distance covered since the last reset
To switch between display functions, press button "i" 1 on
the on-board computer or button "i" 11 on the operating unit
repeatedly until the required function is displayed.
To reset "Trip distance", "Trip time" and "Avg. speed",
switch to any of the three functions and then press and hold
the "RESET" button 6 until the indication is set to zero. This
also resets the values of the other two functions.
To reset the "Max. speed", switch to this function and then
press and hold the "RESET" button 6 until the indication is set
to zero.
To reset "Range", switch to this function and then press the
"RESET" 6 button until the display is reset to the value of the
factory setting.
If the on-board computer is removed from the holder 4, all val-
ues of the features are saved and can still be displayed.
Displaying/Adapting Basic Settings
The basic settings can be displayed and changed regardless
of whether the on-board computer is inserted in the holder 4
or not. Some settings are visible and changeable only when
the operating computer is inserted. Some menu items may be
missing depending on the equipment of your eBike.
To access the basic settings menu, press and hold the
"RESET" button 6 and the "i" button 1 until "Configuration"
is displayed in text indication d.
To switch between the basic settings, press button "i" 1 on
the on-board computer repeatedly until the required basic
setting is displayed. If the on-board computer is inserted in
the holder 4, you can also press button "i" 11 on the operat-
ing unit.
To change the basic settings, press the On/Off button 5 next
to indication "–" to reduce or scroll down, or the lighting but-
ton 2 next to indication "+" to increase or scroll up.
If the on-board computer is inserted in the holder 4, it is also
possible to change using buttons "–" 12 and "+" 13 on the
operating unit.
To exit the function and save a changed setting, press the
"RESET" button 6 for 3 s.
The following basic settings are available:
– "– Clock +": The current time can be set here. Pressing
(1 s)
and holding the setting buttons fast-forwards the setting
speed.
– "– Wheel circum. +": You can change this value pre-set by
the manufacturer by ± 5 %. This menu item is displayed
only when the on-board computer is in the holder.
– "– English +": You can change the language of the text indi-
cations. You can choose between German, English, French,
Spanish, Italian, Portuguese, Swedish, Dutch and Danish.
– "– Unit km/mi +": The speed and distance can be dis-
played either in kilometres or miles.
Bosch eBike Systems