Initial Operation - Bosch PowerPack 300 Notice Originale

On-board computer
Article number
Max. charging current,
USB connection
Charging voltage,
USB connection
1)
USB charging cable
Operating temperature
Storage temperature
Charging temperature
2)
Protection type
Weight, approx.
1) Not included in standard scope of delivery
2) When USB cover is closed
Bosch eBike system uses FreeRTOS (see www.freertos.org)
Bike lights*
Rated voltage
Power output
– Front light
– Rear light
* Not possible via the eBike battery pack in all country-specific versions,
depending on the statutory regulations
Assembly
Inserting and removing the battery pack
For inserting and removing the eBike battery pack in/from the
eBike, please read and observe the battery pack operating in-
structions.
Inserting and removing the on-board computer
(see figure A)
To insert the on-board computer 3, slide it from the front into
the holder 4.
To remove the on-board computer 3, press the lock latch 15
and slide the on-board computer toward the front out of the
holder 4.
 Remove the on-board computer when you park the
eBike.
It is possible to secure the on-board computer against remov-
al in the holder. To do so, remove the holder 4 from the han-
dlebar. Put the on-board computer in the holder. Screw the
locking screw 16 (thread M3, 8 mm long) from below into the
thread provided in the holder. Mount the holder back onto the
handlebar.
Bosch eBike Systems
Intuvia
1 270 020 909
mA 500
V
1 270 016 360
°C –5...+40
°C –10...+50
°C 0...+40
IP 54 (dust and splash
water protected)
kg 0.15
V
W 8.4
W 0.6
Checking the Speed Sensor (see figure B)
The speed sensor 17 and its spoke magnet 18 must be
mounted in such a manner that the spoke magnet, after a turn
of the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
Note: If the distance between speed sensor 17 and spoke
5
magnet 18 is too small or too large, or if the speed sensor 17
is not properly connected, the speed indication f will fail, and
the eBike drive unit will operate in emergency mode.
In this case, loosen the screw of the spoke magnet 18 and fas-
ten the spoke magnet to the spoke in such a manner that it runs
past the mark of the speed sensor at the correct clearance. If
the speed is still not being indicated in the speed indication f
after this, please contact an authorised bicycle dealer.
Operation

Initial Operation

Requirements
The eBike system can only be activated when the following
6
requirements are met:
– A sufficiently charged battery pack is inserted (see battery
pack operating instructions).
– The on-board computer is properly inserted in the holder
(see "Inserting and removing the on-board computer",
page English–3).
– The speed sensor is connected properly (see "Checking
the Speed Sensor", page English–3).
Switching the eBike System On/Off
Options for switching on the eBike system:
– If the on-board computer is already switched on when you
insert it into the holder, then the eBike system will be
switched on automatically.
– When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button 5 of the on-
board computer.
– When the on-board computer is inserted, press the On/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
The drive is activated as soon as you step on the pedals
(except when in the push assistance/start assistance func-
tion, see "Switching the Push/Start Aid On/Off", page
English–5). The motor output depends on the settings of the
assistance level on the on-board computer. As soon as the
system is activated, "Performance Line/Performance
Line CX" will appear briefly on the display.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25/45 km/h, the assis-
tance from the eBike drive is switched off. The drive is auto-
matically re-activated as soon you start pedaling again and the
speed is below 25/45 km/h.
English–3
0 276 001 SPI | (3.6.15)