Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Designed to provide improved lift assist for Ultrex motors equipped with both a Humminbird® MEGA 360 Imaging
Imaging TargetLock
TM
.
Item /
Part #
Description
Assembly
2298411 GAS SPRING, U1.5
2
2298415 GAS SPRING, U1.5
2298412 GAS SPRING, U1.5
A
2994956 BAG ASM, LIFT ASSIST ACC
Item 4
4
2373434 SCREW-1/4-20 X 3/4 SS PPMS
TOOLS AND RESOURCES REQUIRED
• 1/4" Allen Wrench
• Torque Wrench
MOUNTING CONSIDERATIONS
The Ultrex Lift Assist Cylinder reduces the effort required for stowing and deploying the trolling motor when both the Humminbird 360
Imaging and MEGA Live Imaging TargetLock accessories are installed. To accomplish the successful installation of the Lift Assist Cylinder,
please give consideration to the following:
• Complete the installation of both the Humminbird 360 Imaging
and MEGA Live Imaging TargetLock accessories before
beginning the installation of the Lift Assist Cylinder. Use the
installation instructions provided with the product to complete
the installation. Keep the accessories installed to the trolling
motor during the installation.
• Ensure that the trolling motor installation is complete. Follow
the installation instructions provided with the trolling motor or
online at minnkota.johnsonoutdoors.com. The trolling motor
installation should be complete before beginning installation
on the Lift Assist Cylinder.
• Ensure that the trolling motor is not connected to a power source
during the installation to avoid unexpected motor operation.
• During the installation, the load bearing benefits of the Gas
Spring and Lift Assist Cylinder are removed. Minn Kota
recommends using the help of a second person to hold and
secure the Mount during the installation process. Watch for pinch points when working on the installation and do not remove or reinstall
the Steering Module until instructed to do so. Use the help of a qualified marine installer if uncomfortable with the installation.
• If using this Lift Assist Cylinder without the use of the Humminbird accessories, Minn Kota recommends installing the original
Gas Spring.
1 | minnkota.johnsonoutdoors.com
Notes
Qty.
*80/45"*
1
*80/52"*
1
*112/52"*
*112/45"*
1
1
2
• #3 Phillips Screwdriver
• 1/4" Socket Wrench
ULTREX LIFT ASSIST CYLINDER
80/45", 80-112/52" & 112/45"
1854070, 1854071 & 1854072
A A
4 4
• A second person to help
with the installation
CAUTION
Avoid any unexpected motor operation while performing work
on the trolling motor. Disconnect the trolling motor from the
battery or power source before beginning any work.
WARNING
The gas-assist lift mechanism in this unit is under high spring
pressure when the motor is in the deployed position. Do not
remove the Steering Module assembly from the mount without
disconnecting one end of the Gas Spring. Failure to do this can
create a condition where accidental pulling of the Pull Grip and
Cable may cause the mount to spring open rapidly, striking
anyone or anything in the direct path.
and MEGA Live
TM
2 2
• blue thread locker
©2023 Johnson Outdoors Marine Electronics, Inc.
Publicité
Manuels Connexes pour MINN KOTA 80/45
Sommaire des Matières pour MINN KOTA 80/45
- Page 1 Steering Module until instructed to do so. Use the help of a qualified marine installer if uncomfortable with the installation. • If using this Lift Assist Cylinder without the use of the Humminbird accessories, Minn Kota recommends installing the original Gas Spring.
- Page 2 INSTALLATION Disconnect the Gas Spring Disconnect the Gas Spring before removing the Steering Module. The Gas Spring is under high spring pressure. Disconnecting the Gas Spring removes the load-bearing benefits of the Gas Spring. The Gas Spring will be replaced with the new Lift Assist Cylinder when the installation is complete.
- Page 3 Remove Steering Module from Mount Removing the Steering Module removes a large portion of the weight that the Gas Spring displaces. Removal of the Steering Module allows for increased mobility of the Mount to assist in installing the new Lift Assist Cylinder. With the Gas Spring disconnected, place the motor in the deployed position.
- Page 4 Remove the Gas Spring from the Mount The Gas Spring should be completely uninstalled to provide access for installing the new Lift Assist Cylinder. Minn Kota recommends having a second person help hold the Mount while the Gas Spring is removed. When the Gas Spring is disconnected, the weight of the Mount is no longer supported.
- Page 5 With the Yoke rotated, access and remove the two Outer Outer Outer Outer Hex Head Flange Screws holding the Rod End of the Gas Spring to the Yoke. One screw is located on each side of the Yoke. Use a 1/4” Socket Wrench to loosen and remove the Screws.
- Page 6 ITEM(S) NEEDED #2 x 1 Take the List Assist Cylinder (Item #2) and position Flat Surface Flat Surface it above the open Mount. The Gas Spring should of Bracket of Bracket Gas Spring Gas Spring be horizontal to the Boat Deck, with the Bracket Rod End Rod End pointing toward the Outer Arm between the...
- Page 7 Hex Head #2293408) are misplaced, additional screws can be Flange Screw Flange Screw ordered online at minnkota.johnsonoutdoors.com. Yoke Yoke Minn Kota recommends applying blue thread NOTICE: Alignment Alignment locker to the Hex Head Flange Screws before reinstalling. Hex Head Hex Head...
- Page 8 The final step is installing the new Lift Assist Cylinder to gain the benefits of the new cylinder is to secure it to the Outer Arm. Take care to stow and position the motor to connect the List Assist Cylinder to prevent damage to the Gas Spring. Minn Kota recommends using the help of a second person to position and secure the Mount during this final step of the installation.
- Page 9 Utilisez l’aide d’un installateur marin qualifié si vous ne vous sentez pas à l’aise avec l’installation. • Si vous utilisez ce cylindre d’assistance au levage sans utiliser les accessoires Humminbird, Minn Kota recommande d’installer le ressort à gaz d’origine.
- Page 10 INSTALLATION Débranchez le ressort à gaz Vous devez déconnecter le ressort à gaz avant de retirer le module du gouvernail. Le ressort à gaz est sous haute pression. Débrancher le ressort à gaz élimine les avantages liés à la charge du ressort à gaz. Le ressort à gaz sera remplacé par le nouveau cylindre d’assistance au levage une fois l’installation terminée.
- Page 11 Retirez le module du gouvernail du support Le retrait du module du gouvernail supprime une grande partie du poids que le ressort à gaz déplace. Le retrait du module du gouvernail permet une mobilité accrue du support pour aider à installer le nouveau cylindre d’assistance au levage. Lorsque le ressort à...
- Page 12 Retirer le ressort à gaz du support Le ressort à gaz doit être complètement désinstallé pour permettre l’installation du nouveau cylindre d’assistance au levage. Minn Kota recommande qu’une deuxième personne aide à tenir le support pendant que le ressort à gaz est retiré. Lorsque le ressort à gaz est débranché, le poids du support n’est plus supporté.
- Page 13 Avec la fourche tournée, accédez aux deux vis à Bras Bras Bras Bras externe externe tête hexagonale d’accouplement qui retiennent externe externe l’extrémité de la tige du ressort à gaz à la fourche et Ressort Ressort à gaz à gaz retirez-les.
- Page 14 ARTICLE(S) REQUIS #2 x 1 Prenez le cylindre d’assistance au levage (article Surface plate Surface plate nº 2) et placez-le au-dessus du support ouvert. du coudé du coudé Extrémité Extrémité Ressort à gaz Ressort à gaz Le ressort à gaz doit être horizontal par rapport de la tige de la tige au pont du bateau, le coudé...
- Page 15 Vis à tête hexagonale Fourche Fourche d’accouplement d’accouplement Minn Kota recommande d’appliquer un frein-filet AVIS : bleu sur les vis à tête hexagonale d’accouplement avant de les réinstaller. Réinstaller le module du gouvernail Remplacez le module du gouvernail avant de connecter le cylindre d’assistance au levage pour vous assurer que le poids du module du gouvernail et des accessoires Humminbird est dispersé...
- Page 16 Prenez soin de ranger et de positionner le moteur pour connecter le cylindre d’assistance au levage afin d’éviter d’endommager le ressort à gaz. Minn Kota recommande d’utiliser l’aide d’une deuxième personne pour positionner et fixer le support pendant cette dernière étape de l’installation.