Publicité
Les langues disponibles
Les langues disponibles
• CHECK TO MAKE SURE THAT THE
CAR SEAT OR THE BABY CARRIAGE
IS CORRECTLY FASTENED TO THE
STROLLER (WHERE APPLICABLE).
• DO NOT DRIVE THIS PRODUCT
AROUND STAIRS OR STEPS; CARE MUST
BE TAKEN IF UNIT IS USED ON STAIRS
OR ESCALATORS.
• DO NOT USE THE PRODUCT IF IT HAS
BROKEN OR MISSING PARTS.
• DO NOT USE NEAR FIRE OR EXPOSED
FLAME.
• NOTICE: THIS ARTICLE MEETS OR
EXCEEDS ALL REQUIREMENTS
COVERED IN ASTM F833 STANDARD
AND LATEST REVISIONS.
instructions for use
ASSEMBLING THE WHEELS
1• Remove the four protection caps (two round
ones and two square ones) from the chassis
while it is still folded up, as shown in the figure.
2• Mount the front wheels with the chassis folded,
pressing on the attachment lever (figure A) and
inserting the hub onto the rod (figure B). Check
to make sure the wheels are correctly attached
by pulling them in opposite directions.
3• Repeat the same operation on the rear wheels
as for the front wheels (steps A and B).
• Check to make sure the brake gear is correctly
installed.
BRAKE
4• To set the brake on the chassis, lower the brake
bar on the rear wheels, as shown in the figure.
OPENING THE CHASSIS
• Set the brake while the chassis is still folded up.
5• Unfasten the tab, as shown in the figure.
6• Lift the handlebar in the direction shown by the
arrow.
7• Press the handlebar downwards until it clicks
into the final position.
8• To make sure the chassis is correctly open,
check the illustration.
BASKET
9• The basket goes at the base of the chassis, as
shown in the figure.
10• The basket fastens to six different points. First,
fasten it to the four buttons in the front and
back, as shown in figure A and B. Then fasten
the two straps to the chassis pipe, as shown in
figure C.
STEERING WHEEL
11• To allow a good grip, the steering wheel can be
adjusted to four different positions by pressing
on the button shown in the figure.
SWIVEL WHEELS
12• The practical steering wheel has a lever for
swiveling the front wheels. Move the lever on
the steering wheel to the right to swivel the
front wheels, as shown in figure A. To set the
wheels on stationary, use the lever on the left,
as shown in figure B.
OUTER HANDLES
13• The chassis can be completely lifted off the
ground using the center, outer handles and
the large back handle, as shown in the figure. It
takes two people to lift the chassis.
14• The figure shows the correct way to lift the
chassis.
REMOVING THE WHEELS
15• To remove the wheels, press the lever on the
center of the wheel, as shown in the figure, and
pull the wheel towards yourself.
FOLDING UP THE CHASSIS
• Set the brake and unfasten the seats.
16• To fold up the chassis, lift the lever on the large
handle as shown in the figure, unfastening the
handlebar and moving it slightly forward.
17• Use your left foot to press the safety lever
downward to loosen the handlebar, as shown
in the figure.
18• Turn the handlebar downward, as shown in the
figure.
19• Fold up the chassis, fastening the tab to the
hook on the handlebar.
ganciomatic system
To meet your specific needs, the Ganciomatic
System allows you to fasten the car seat or the
carrying seat to the Duette SW chassis. Please
follow the instructions for combining various
products.
DUETTE + 2 CARRIER SEATS
ATTENTION:
• To ensure greater stability, we recommend
installing both carrier seats at all times.
• If for any reason DUETTE SW is used with only
one occupant, we recommend attaching both
carrier seats in any case. Make sure the seats are
securely attached.
20• For instructions on how to attach and detach
the product from the chassis, see the manual
supplied with the carrier seat. Figures A, B, C,
and D show different ways to attach the seats.
• Figure D shows the "crib" position, with the
backrest completely lowered and the footboard
raised as shown in the figure.
DUETTE + 2 PRIMO VIAGGIO CAR SEATS
21• Figure A shows how to attach the product
(with the seat turned towards the mother).
Publicité
