Operating Instructions; Adjustment Operations; General Instructions - stayer BJ120 Instructions D'emploi

30 Arrow of direction of rotation of the spindle for milling
Top 31 metal
32 Screw for fixing the metal plate
33 Motherboard
The accessories illustrated or described are not within the
material attached as standard. The full range of
accessories can be found in our program accessories.

4. Operating instructions

4.1 Adjustment Operations

Adjusting the cutting depth
The knob 18 can set the depth of fresado.El knob can be
locked in three positions different height for different sizes
of biscuit.
Interrelationship between locking heights, cookies, and
milling depths:
Height
biscuit
locking
0 Nº0
10 Nº10
20 Nº20
S Simplex
D Duplex
By employing disc cutters sharp it may be necessary
readjust the cutting depth. For this, loosen the lock nut 19.
Turning to the effect clockwise the knurled screw 20 can
be reduced milling depth, and vice versa. Take a milling
Test for controlling the cutting depth adjusted. Once com-
pleted the adjustment, tighten the locking nut 19.
Adapting the top of vertical adjustment
The top vertical adjustment 9 allows you to set the dis-
tance between the upper face of the piece and the slot
milling.
To mount the top of vertical adjustment 9 seat it against
stop for angles 17 and round it with the dial 8 against stop
guide for angles.
Note: Do not exert any force to During installation!
When mounted in the correct position, the stop 9
slides smoothly.
Set the dial 8 according to the desired distance scale hei-
ght 4. Close then the levers 12 tightening.
To position the slot in the middle is necessary to adjust
vertical to the top half of the setting part thickness.
To remove the top of vertical adjustment loosen the lever 9
12 and actuate clamping levers 8 for rotating remove the
stop up the top for 17 angles.
ENGLISH
Milling depth
in mm
8
10
12.3
13
14.7
18
Adjusting the angle milling
The stop 17 allows to make angles with ease milled in
mitered seams. To reset the stop angles loosen the levers
17 Tightening 3. Tilt the top angles until the desired angle
scale in angle 5 (there notches at 0 °, 45 ° and 90 °). Then
close the lever Tightening 3.
Start up
Note the mains voltage! The supply voltage
tion must match the on the nameplate of the
tool supply. Power tools marked 230V 220V
can work well.
The machine must only connected if the base
plate 33 has been firmly locked with the screw
32 and the metal cap 31 of safety precautions.
Before connecting the appliance, make sure
the mechanism to work properly Automatic re-
trieval engine unit:
Press Exit strawberry aganst the edge of a table, eg visi-
ble until the cutter disk. By reducing pressure, the cutter
disk must be fully retracted on the motherboard.
Switching on / off
For connecting the machine, push forward the switch on
/ off 2 and press forward and downward to engage. to
switch off the machine, push back the switch / off switch
2, so that this skip to save energy desconexión.Para po-
sition, Only connect the machine when you go to use it.

4.2 General Instructions

Positioning milling
The vertical centerline 11 of the top brand for angles and
height stop indicates the center of milling (perpendicular
the milling cutter). The maximum width of milling the
indicate both brands top 10 of vertical adjustment in 9.
For positioning height serves as guidance horizontal
centerline 6 mark on the motherboard, as indicel center of
the milling cutter.
The arrow 13 in the housing of the power tool shows the
direction of rotation of the cutter disk.
Milling unions
Examples of these types of union finds in the illustrated
pages:
- Butt joint: with stop angles, with adjustment cap
vertically.
- Miter: with stop angles, with stopper vertical adjustment.
- Longitudinal and transverse Empalme: with stop
angles, vertical adjustment cap.
- Union of frames.
- Union of intermediate boards.
18