Instructions For Use; Placement Tool; Assembly; Electrical Connection - stayer SD27BE Instructions D'emploi

Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
Safety warnings specific for wire brushing operations
Be aware that wire bristles are thrown by the brush
Ÿ
even during ordinary operation. Do not overstress
the wires by applying excessive load to the brush.
The wire bristles can easily penetrate light clothing
and/or skin.
Allow brushes to run at operating speed for at least
Ÿ
one minute before using them. During this time no
one is to stand in front or in line with the brush. Loose
bristles or wires will be discharged during the run-in time.
Direct the discharge of the spinning wire brush
Ÿ
away from you. Small particles and tiny wire fragments
may be discharged at high velocity during the use of
these brushes and may become imbedded in your skin.
Additional safety warnings
Wear safety goggles.
Use suitable detectors to determine if utility lines
Ÿ
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
Release the On/Off switch and set it to the off
Ÿ
position when the power supply is interrupted, e. g.,
in case of a power failure or when the mains plug is
pulled. This prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
Ÿ
clamping devices or in a vice is held more secure than by
hand.

3.Instructions for use

3.1 Placement Tool

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.

3.2 Assembly

Before any work on the machine itself, pull the mains
plug.
Mounting the Grinding Tools (see figure A)
Only use properly fitting and undamaged open-
end spanners.
– Clean the grinder spindle 3 and all parts to be mounted.
– Hold the grinder spindle 3 with spanner 8 by the spanner
flats.
ENGLISH
17
Loosen the clamping nut 2 with spanner 8 by applying it
to the spanner flats and turning in anticlockwise
direction.
– Insert the clamping shaft of the grinding tool to the stop
into the collet chuck 1.
– Hold the grinder spindle 3 firmly with spanner 8 and clamp
the tool bit with spanner 8 by the spanner flats, turning in
clockwise direction.
The grinding tools must run completely concentrical. Do not
continue to use out-of-round grinding accessories, instead,
replace before continuing to work.
Do not tighten the collet chuck of the clamping
nut as long as no grinding accessory is mounted.
Otherwise, the collet chuck can become
damaged.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of the
user or bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace.
Dusts can easily ignite.

3.3 Electrical connection

Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.

3.4 Illustrated description

1 Collet chuck
2 Clamping nut
3 Grinder spindle
4 Spindle collar
5 On/Off switch
6 Thumbwheel for speed preselection
7 Handle (insulated gripping surface)
8 Spanner service

4. Operating instructions

4.1 Placement and testing

Switching On and Off
To start the power tool, push the On/Off switch 5 forwards.
To lock the On/Off switch 5, press the On/Off switch 5 down
at the front until it latches.
17