EINHELL 43.007.20 Mode D'emploi D'origine page 15

Anleitung_BT_SM_2050_SPK1:_
Contact with the saw blade in the uncovered saw
zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if essential ear-muffs are not
worn.
Harmful emissions of wood dust when the
machine is used in closed rooms.
5. Technical data
Asynchronous motor
Output
Operating mode
Idle speed n
0
Carbide-tipped saw blade
Number of teeth
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Weight
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
15.06.2010 13:51 Uhr
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
230 V~ 50 Hz
is not properly guided and maintained.
1700 W
S1
4800 min -1
6. Before starting the equipment
ø 210 x ø 30 x 2,8 mm
6.1 General information
24
The equipment must be set up where it can stand
-45° / 0°/ +45°
securely, i.e. it should be bolted to a workbench,
0° to 45° to the left
a universal base frame or similar.
205 x 65 mm All the covers and safety devices have to be
properly fitted before the machine is switched on.
140 x 65 mm
It must be possible for the saw blade to run
freely.
140 x 40 mm
When working with wood that has been
15 kg processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
6.2 Assembling the saw (Fig. 1-5)
86 dB(A)
To adjust the turntable (17), loosen the locking
3 dB
grip (14) by approx. 2 turns, which frees the
turntable (17).
99 dB(A)
Press the locking lever (13), turn the turntable (17)
3 dB
and scale pointer (15) to the desired angular
setting on the dial (16) and lock into place with
the locking grip (14). The saw has locking
positions at angular positions of -45°, -30°, -22,5°,
-15°, 0°, 15°, 22,5°, 30°, 45° at which the locking
lever can be engaged.
To release the saw from its position at the bottom,
pull the locking pin (25) out of the motor mounting
while pressing down lightly on the machine head
(4). Turn the locking pin (25) through 90° before
you release it so that the saw remains released.
Seite 15
GB
15