Publicité
Les langues disponibles
Les langues disponibles
8. Operation
m CAUTION!
Please pay attention to the statutory provisions in the
relevant noise protection regulations.
Before starting the appliance, always check that:
• The fuel system is not leaking.
• The protective equipment and cutting equipment is
complete and in perfect working order.
• All screw connections are firmly tightened.
• All moving parts can move smoothly and freely.
Start the appliance (Fig. 10-13)
Never start or operate the chainsaw if the chain and
the chain brake lever or the front hand guard have
not been properly installed. In addition, always start
with the chain brake active. Proceed as follows for
this:
• Remove the cover (15) from the guide rail (2).
• Place the chainsaw on a firm, level surface. The
saw chain (1) must not touch the ground.
• Push the front hand guard (3) forwards until it clicks
into place. The saw chain (1) will be locked by the
chain brake.
• Press the fuel pump "Primer" (24) 6-10 times.
• Switch the On/Off switch (11) to "ON" (11a).
• Pull the choke (7) out ( ).
• Place the tip of your shoe into the rear hand handle
(9) (see fig. 13).
• Hold the chainsaw firmly by the front handle (4) and
pull the starter pull cord (13) slowly until you feel
resistance.
• Now pull the starter pull cord (13) quickly so that the
engine starts. If the engine does not start, repeat
the process. As long as the choke (7) is out ( ),
the engine will only run for a short time and then
switch off.
• As soon as the engine is off, press the throttle con-
trol lock (8) and the throttle control (10) simultane-
ously. The choke (7) automatically jumps to the
"warm start" operating position.
• Now pull the starter pull cord (13) quickly again so
that the engine starts.
If the engine does not start after several attempts,
read the "Troubleshooting".
m CAUTION!
Always pull the starter pull cord (13) straight out. Hold
the handle of the starter pull cord (13) firmly when the
starter pull cord (13) retracts. Do not allow the starter
pull cord (13) to whip back.
NOTE
At very high outdoor temperatures it is possible that
even a cold engine has to be started without using
the choke!
• Release the chain brake by pulling the front hand
guard (3) backwards (see fig. 14). CAUTION! The
chain brake is now released and the saw chain (1)
now runs freely.
NOTE
If the saw chain (1) moves when it is idling or the en-
gine goes out when you release the throttle, you need
to adjust the carburettor (see section "Maintaining the
carburettor settings").
• Lift the chainsaw.
• Hold the front handle (4) firmly in your left hand.
• Hold the rear handle (9) firmly in your right hand.
The ball of your hand now lies on the throttle control
lock (8) and your index finger operates the throttle
control (10) (see fig. E).
• After pulling the throttle (10), once, the engine
should idle.
• Run the engine to warm it up.
Starting when the engine is hot
(The appliance has been turned off for less than
15–20 minutes)
• Push the front hand guard (3) forwards until it clicks
into place. The saw chain (1) will be locked by the
chain brake.
• Switch the On/Off switch (11) to "ON".
• The choke lever (7) does not need to be pulled out
to start a warm motor.
• Place the tip of your shoe into the rear hand guard
(9) (see fig. 13).
• Hold the chainsaw firmly by the front handle (4) and
pull the starter pull cord (13) slowly until you feel
resistance.
• Now pull the starter pull cord (13) quickly. The ap-
pliance should start after 1–2 pulls. If the appliance
still hasn't started after 6 pulls, repeat the process
as described in "Starting when the engine is cold".
Stopping the motor (Fig.10)
1. Release the throttle lever and wait until the en-
gine is idling.
2. Set the power switch to „Stop (0)" to stop the mo-
tor. (Fig.10/Pos.11b)
m NOTE
To stop the engine in an emergency, activate the
chain brake and set the ON / OFF switch to „Stop".
www.scheppach.com
GB | 47
Publicité
