Publicité
Les langues disponibles
Les langues disponibles
CONTROL SET-UP PROCEDURES
IMPORTANT:
Read all instructions before operating.
The lower fabric setting key pads and the digital display are
used to set up the controls. The display can contain 4 numbers
and/or letters and a decimal point. These are used to indicate
the set-up codes and related code values available for use in
programming the washer.
How to use the key pads to p:rogram the controls
1. The LOWER
LEFT key pad is used to adjust the values
associated with set-up codes. Pressing the key pad will
increment the value. Rapid ajustment is possible by holding
down the key pad.
2. The LOWER
MIDDLE key pad will advance you through the
set-up codes. Pressing the key pad will advance you to the
next available set-up code. Holding down the key pad will
automatically advance through the set-up codes at arate
of one (1) per second.
3. The LOWER
RIGHT key pad is used to select or deselect
options.
Start Operating Set-Up
@
PD Models: Insert access door key, turn, and lift to remove
access door.
@
PR Models: Once the debit card reader is installed (according
to the reader manufacturer's instructions), the set-up mode
can be entered by inserting a set-up card (supplied by the
reader manufacturer) into the card slot. If a manual set-up
card is not available, manual set-up mode can be entered
by removing connector AA1
on the circuit board.
IMPORTANT: The console must not be opened unless power
is first removed from the washer. To access connector AA1:
-
Unplug washer or disconnect power.
~
Open console, disconnect plug on AA1, close console.
-
Plug in washer or reconnect power.
The washer is now in the set-up mode.
NOTE: The control does not need to be set up in order for
the washer to operate. These procedures are to be followed
only to customize the control as desired.
SET-UP CODES
@
The LOWER
MIDDLE key pad will advance from code
to code.
@
The LOWER
LEFT key pad will change the code value.
@
The LOWER
RIGHT key pad will select or deselect options.
FOR PR MODELS: The set-up codes are the same as for the PD
models, except where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
(e10)5) =
|
EXPLANATION
Bin
REGULAR CYCLE PRICE
bin
Represents the number of coins (coin 1); may adjust
from 0-39. (See VALUE OF COIN 1.) Advance from
0-39 by pressing the LOWER
LEFT key pad. Factory
preset for 7 coins = $1.75.
PR MODELS
ONLY: Factory preset for 0 coins.
~ Press the LOWER MIDDLE key pad once to advance to next code.
10
CODE
EXPLANATION
WASH LENGTH
This is the number of minutes for WASH.
Choose from 8-20 minutes by pressing the LOWER
LEFT key pad.
~ Press the LOWER MIDDLE key pad once to advance to next code.
fel
RINSE CYCLES
acl
This is the length and total number of rinses. Each
rinse agitation is 1-4 minutes, with a choice of 1
or 2 rinses. The middle digit is the length of rinse
agitation and the right digit is the number of rinses.
The number is changed in the following sequence
(11, 21, 31, 41, 12, 22, 32, 42) by pressing the
LOWER
LEFT key pad.
Press the LOWER
MIDDLE key pad once to advance
to next code.
The DELICATES & KNITS cycle has a fixed rinse
agitation length of one minute.
~ Press the LOWER MIDDLE key pad once to advance to next code.
Gud
CYCLE COUNTER OPTION
This option is either SELECTED
"ON" or NOT
SELECTED "OFF."
Sug
Not Selected "OFF."
SAE
Selected "ON" and not able to be deselected.
Press the LOWER
RIGHT key pad 3 consecutive
times to select "ON." Once selected "ON" it cannot
be deselected.
~ Press the LOWER MIDDLE key pad once to advance to next code.
ig
MONEY COUNTER OPTION
This option is either SELECTED
"ON" or NOT
SELECTED "OFF."
Leg
Not Selected "OFF."
ie
Selected "ON."
Press the LOWER
RIGHT key pad 3 consecutive
times to select "ON" and 3 consecutive times to
remove (Not Selected "OFF.") Counter resets by
going from "OFF" to "ON."
ied
Selected "ON" and not able to be deselected.
To select "ON" and not able to be deselected, first
select "ON," then within two seconds press the
LOWER
RIGHT key pad twice, the LOWER
LEFT
key pad once, and exit the set-up mode.
~ Press the LOWER MIDDLE key pad once to advance to next code.
ee
SPECIAL PRICING OPTION
This option is either SELECTED
"ON" or NOT
SELECTED "OFF."
ou
Not Selected "OFF."
CoF
Selected "ON." Press the LOWER
RIGHT key pad
once for this selection.
if SPECIAL PRICING OPTION
is selected, you have access
to codes "3." through "9.".
~ Press the LOWER MIDDLE key pad once to advance to next code.
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
ay
SPECIAL CYCLE PRICE
3H]
Represents the number of quarters (coin 1): may
adjust from 0-39. (See VALUE OF COIN 1.) Advance
from 0-39 by pressing the LOWER
LEFT Key pad.
Factory preset for 7 coins = $1.75.
PR MODELS
ONLY: Factory preset for 0 coins.
~ Press the LOWER MIDDLE key pad once to advance to next code.
Publicité
