Backer Panels
Dispenser Frame (dispenser models only)
NOTES:
m
Dashed lines represent backer panel placement.
mg
lilustration shows backer panels placed on decorative
overlays.
[*
c
*|
Ber
ns
;
1
>
Ke
a em)
j,._-_-----------
- --- | Side Offset
Yo" (12.7 mm)
Bottom Offset
Top Offset
Vo" (1.27 cm)
Y 1s" (4.13 om)
i}
oe
i
tho
;
'
1
'
1
'
I
'
1
'
1
'
I
'
22"
1
'
1
'
I
1 (65.9em)
!
'
mete
lel
'
'
'
' )
Handle-
'
!
1
'
1
1 |Side Offset} 1
'
1iu
t
A—!
;
yi
1
1y¥_
4
1
'
(6.4mm)
| ,
'
'
1
'
I
I
I
I
I
I
I
I
I
'
1
'
I
'
1
'
I
I
I
I
I
!
170%"
|
1 70%"
1 (179.10m)
;
1 (179.1 cm)
\
"SSI
'
I
I
l
I
I
I
I
1
!
I
t
'
\
'
'
I l
I
I
I
1
!
I
1 334"
'
1
1
1
1
| (845m)
1
'
'
1
!
'
I
1
!
'
I
I
I
1
!
I
I
I
I
1
!
I
I
I
I
1
!
I
I
\
I
1
I
i
I
\
I
1
I
i
I
\
I
1
I
i
I
\
I
1
I
i
!
y o
|
!
!
!
!
A>!
<— A
<}—— B >}
!
!
_V¥___!
_v.
4
_y LY
__e eee 3
A
Bottom Offset
A
Bottom Offset
A
Ye" (3.2 mm)
Ye" (3.2 mm)
Model
A
B
Cc
42
1697/4" (42.55 cm)
223/4" (57.79 cm) | 39/4" (100.97 cm)
48
19174" (48.90 cm)
261/4" (66.68 cm) | 453/4" (116.21 cm)
14
The dispenser frame attaches to the panel with 4 screws.
A. Decorative panel
B. Refrigerator door
C. Dispenser frame
The dispenser frame overlaps the dispenser cutout by "6"
(0.78 cm) on each side and 12" (1.27 cm) on the top and bottom.
A. ¥%" (1.27 cm) Overlap
g
a
y Gs
is
Custom side panels may be needed when
not t enough
space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an Inset, Flush, or Recessed Inset panel installation.
Euro-Siyle
oO
io
i
rg oe
&
"ust
m\ "ght
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
m
Thedimensions shown are actual product dimensions and
may not reflect the needed panel installation dimensions.
m
The side panel should be a minimum of ¥2" (1.27 cm) thick
to avoid warping.
m_
If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on rear wall.