Publicité
Les langues disponibles
Les langues disponibles
6 - INsIGhTs - ADVANCED MENU
The ADVAnCED MEnu allows you to further customize the instal-
lation by changing some parameters not accessible from the basic
menu
To access the ADVAnCED menu, hold down the MEnu button for 5
seconds. To change the parameters of the ADVAnCED MEnu pro-
parameters
Deceleration lenght
1
Determines how far in advance reduced speed is imposed to
the switch's stop.
ramp acceleration and deceleration time.
2
the lower the value, the shorter and sharper is the ramp.
impact force on obstacle: allows faster reaction time on the
3
obstacle (e.g. impact in the absence of rubber edge), lower
value = faster reaction time
further acceleration at start. useful to speed up the opening
4
of the barrier.
obstacle/edge reverse time (0 = disabled)
5
pedestrian opening lenght
6
Determines the partial opening of the installation from the
closeD position.
7
pedestrian opening automatic auto-reclosing time
Photocell F2 configuration
0.
8
1.
9
enables opening with f1 obscured
Man Present configuration (only for open/close inputs)
0.
10
1.
clearance. allows to stop before the fully open position: it is
11
useful to avoid mechanical stress during opening.
Pre-flashing time
12
13
courtesy light timer
courtesy light configuration
14
1. on if courtesy light timer tcy is not expired
2. on if the gate is not closed + tcy time
courtesy litht level at the end of the manouvre (0 = light is off,
15
other values light will stay on all the time at the desired level)
Open gate light configuration
0.
1.
2.
16
cycles before maintenance (0 = disabled). When level set is
reached the next cycles will be done with a fast flashing to
17
advise the user
Enables the constant flashing of the request for maintenance
(function performed only when the gate is closed)
18
Under battery back-up flashing will not be performed
number of encoder impulses per motor revolution
19
sets default values and type of control
0.
20
1.
2.
To set the default values: 1) Enter the advanced programming 2) Select the "dEf" parameter 3) Activate the edit mode (displays "0" flashing)
4) Accept the change (press "MEnu" button for 2 seconds). At this point you should see a countdown d80,d79.....d02,d01
* nEP value depends on motor encoder typology.
* Values for 400 Kg sliding motors.
All manuals and user guides at all-guides.com
Description
enabled for both opening and closing op/cl
enabled only for opening op
0. Disabled
1. man present
on/off
modulated by the position of the gate
magnetic electric lock function ( interface with a
24V external relay). to activate this function it is
necessary to activate also pre-flashing for 1 sec.
(tpr = 1)
sliding
Barrier
sliding 400 Kg (nep=1*) - lsi blocked at 50
ceed as indicated for the bASIC MEnu
In the last column are indicated the parameters used only for a
specific type of automation: SL sliding motor, BA barrier, BL over-
head, SE sectional.
Default
min
50
10 (30*)
50
1
3
50
20
0
1
0
0
0
0
1
0
0
0
0
4
0
max
unit
cm
0
200
(step 10)
10
30
0
100
0
1
0
20
s
cm
0
990
(step 10)
s
0
600
(step 10)
0
1
0
1
0
1
0
100
0
10
s
s
0
900
(step 10)
1
2
0
100
0
2
1000
0
100
cycles
0
1
1
16
0
1
EN
type
Ba
sl
sl
sl
Ba
sl
23
Publicité
