Opening And Closing Doors; Using The Controls; Refrigerator Use - Whirlpool GI7FVCXXA Instructions D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be
opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.
When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.
When both doors are closed, the hinged seal automatically
forms a seal between the two doors.
A. Hinged seal

Using the Controls

The refrigerator and freezer controls are located on the dispenser
panel and display screen.
A
A. Display screen
Language Selection
The language of the text on the display screen can be set to
English, Spanish or French.
To change the display screen text from English to Spanish or
French, press the HOME button on the dispenser panel. On
the display screen, press OPTIONS, then PREFERENCES,
then LANGUAGE. Select ESPAÑOL (Spanish) or FRANÇAIS
(French), wait 15 seconds or press BACK, and the screen text
will be changed.
To change the display screen text from Spanish to English,
press the HOME button on the dispenser panel. On the
display screen, press OPCIONES, then PREFERENCIAS, then
IDIOMA. Select INGLÉS, wait 15 seconds or press ATRÁS,
and the screen text will be changed.
8

REFRIGERATOR USE

To change the display screen text from French to English,
press the HOME button on the dispenser panel. On the
display screen, press OPTIONS, then PRÉFÉRENCES, then
LANGUE. Select ANGLAIS, wait 15 seconds or press
RETOUR, and the screen text will be changed.
Temperature Controls
For your convenience, your refrigerator and freezer controls are
preset at the factory. When you first install your refrigerator, make
sure that the controls are still set to the "mid-settings."
To view set points, press the TEMP button on the dispenser panel.
A
The factory recommended set points are 0°F (-18°C) for the
freezer and 38°F (3°C) for the refrigerator.
IMPORTANT:
Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a higher (colder) than
recommended setting will not cool the compartments any
faster.
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
The display screen on the dispenser control panel has a
backlight, which will turn off automatically when the controls
have not been used for 2 minutes or more. When the backlight
is off, the first press of a control button or the display screen
will only reactivate the backlight, without changing any
settings. Within 2 minutes after the backlight has been
reactivated, additional presses of control buttons or the
display screen will change the applicable settings.
Adjusting the Controls
To adjust the set points, press the TEMP button on the dispenser
panel. Set points and adjusting information will appear on the
display screen.
Refrigerator Controls
Make sure REFRIGERATOR is selected. The up and down arrows
on the display screen allow you to adjust the refrigerator
compartment temperature. The set point range for the refrigerator
is 33°F to 45°F (0°C to 7°C).
Press the down arrow to lower the set point.
Press the up arrow to raise the set point.
NOTE: To view Celsius temperatures, press UNITS. To return
the display setting to Fahrenheit, press UNITS again.
Freezer Controls
Make sure FREEZER is selected. The up and down arrows on the
display screen allow you to adjust the freezer compartment
temperature. The set point range for the freezer is -5°F to 5°F
(-21°C to -15°C).
Press the down arrow to lower the set point.
Press the up arrow to raise the set point.
NOTE: To view Celsius temperatures, press UNITS. To return
the display setting to Fahrenheit, press UNITS again.

Publicité

Table des Matières
loading

Table des Matières