Table Des Matières; Declaration Of Conformity - Walther PILOT WA 900 Instructions De Service

Contents
Exploded Drawing
Declaration of CE-Conformity
List of Replacement Parts
1 General
1.1 Identification of Model Version
1.2 Normal Use
1.3 Improper Use
2 Technical Description
3 Safety Warnings
3.1 Safety Warting Symbols
3.2 Generally Applicable Safety Precautions
4 Assembly / Installation
4.1 Radial or circulation method
4.2 Mounting of Spray Gun
4.3 Connection of Input Lines
5 Operational Handling
5.1 Safety Warnings
5.2 Starting/Stopping Requirements
5.3 Spray Pattern Test
5.4 Spray Pattern Adjustments
5.5 Retooling of Spray Gun
5.6 Conversion of adapter plate from radial to circulation method
6 Cleaning
6.1 Safety Warnings
6.2 Cleaning - Complete
6.3 Cleaning - Routine
7 Repairs / Replacements
7.1 Replacement of defective Needle Seal Packings
7.2 Replacement of Nozzles, Needles, Springs and Seals
8 Trouble shooting and Corrective Action
9 Disposal of Cleaning / Servicing Substances
10 Specification Data
2
29
30
36
36
36
37
37
38
38
39
39
39
40
40
41
41
41
41
42
43
44
44
44
44
46
46
46
47
48
48
49
28

Declaration of Conformity

We, the manufacturers of the equipment, hereby declare under our sole responsibility that the
product(s) described below conform to the essential safety requirements. This declaration will be
rendered invalid if any changes are made to the equipment without prior consultation with us.
Manufacturer WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18 - 30
D - 42327 Wuppertal
Tel.: +49(0)202 / 787 - 0
Fax: +49(0)202 / 787 - 2217
www.walther-pilot.de • e-mail: info@walther-pilot.de
Type Designation Automatic Spray Guns PILOT WA 900-Models
WA 900
WA 905
WA 920-HVLP
WA 925-HVLP
WA 940-HVLP PLUS
WA 945-HVLP PLUS
WA 903-K
WA 908-K
WA 923-HVLP-K
WA 928-HVLP-K
Intended purpose Processing of sprayable media
Applied Standards and Directives
EU-Mechanical Engineering Directives 2006/42/EC
2014/34/EU (ATEX Directives)
DIN EN ISO 12100
DIN EN 1953
DIN EN 1127-1
Specification according 2014/34/EU
Category 2 Part marking
Authorized with the compilation of the technical file:
Nico Kowalski, WALTHER Spritz- und Lackiersysteme GmbH, Kärntner Str. 18 - 30
D- 42327 Wuppertal
Special remarks :
The named product is intended for installation in other equipment. Commissioning is prohibited
until such time as the end product has been proved to conform to the provision of the Directives
2006/42/EC.
Wuppertal, the 2nd of November 2016
p.p.
Name: Torsten Bröker
Position: Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability. The safety instructions
provided in the product documentation must be observed at all times.
(Standard with internal control)
(Standard without internal control)
(Low pressure with internal control)
(Low pressure without internal control)
(Mediem pressure with internal control)
(Mediem pressure without internal control)
(Standard adhesive with internal control)
(Standard adhesive without internal control)
(Low pressure adhesive with internal control)
(Low pressure adhesive without internal control) V 21 928
DIN EN 13463-1
DIN EN 13463-5
Tech.File,Ref.:
II 2 G c T 5
2416
29
V 21 900
V 21 905
V 21 920
V 21 925
V 21 940
V 21 945
V 21 903
V 21 908
V 21 923