Black & Decker KR540 Mode D'emploi page 23

All manuals and user guides at all-guides.com
• The adjustable depth stop gives precise control of
the hole depth, when you drill blind holes.
FITTING THE DRILL BIT (KEYLESS CHUCKS)
Disconnect the plug from the electricity supply.
Insert the drill bit in the jaws of the chuck. Hold the
rear section of the chuck while tightening the front
section. Twist the two sections firmly in opposite
directions to securely grip the drill bit.
FITTING THE DRILL BIT (KEYED CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
the end of the chuck key in one of the three holes in
the body of the chuck, ensuring the head of the
chuck key is engaged with the barrel of the chuck.
Turn the chuck key clockwise to tighten the jaws and
securely grip the drill bit. Remove the chuck key.
REMOVING THE CHUCK (KEYLESS CHUCKS)
Proceed as follows:
To remove the chuck, open the jaws, hold it firmly in
one hand and with a screwdriver held in the other
hand, turn the set-screw in the chuck clockwise
approximately one turn, to loosen it.
loosen the chuck on the spindle. Remove the allen
key. Use the screwdriver to turn the set-screw
clockwise until it totally disengages from the spindle.
KR540-600 ML p20-34
Remove the chuck from the spindle by rotating it
anti-clockwise. To fasten the chuck, put it on the
thread and turn it clockwise until it stops. Put in the
screw and turn it anti-clockwise until absolutely firm.
While holding the
REMOVING THE CHUCK (KEYED CHUCKS)
rear section of
Proceed as follows:
the chuck, rotate
the front section
until the jaws of
the chuck are
sufficiently open.
the chuck clockwise with the other hand until it comes
out. Use only the correct chuck key. Place the chuck
key into the chuck, and hold the drill firmly in one hand
with the chuck pointing away from you. Rotate the
Rotate the barrel
chuck so that the chuck key is just above the horizontal
of the chuck until
position on the right hand side of the machine. Give the
the jaws are
crossbar end of the key a sharp downward blow with a
sufficiently open.
mallet or light hammer. The chuck should now be
Insert the drill bit
sufficiently loose to be unscrewed by hand.
in the jaws of the
chuck. Insert the
FITTING THE SIDE HANDLE
chuck key with
Proceed as follows:
position. Tighten the handle by turning clockwise.
SETTING THE ADJUSTABLE DEPTH STOP
Proceed as follows:
Place an allen key
P P y y @ @ @ @ P P @ @ P P @ @ @ @ P P @ @ P P @ @ P P @ @ P P @ @ P P P P @ @ @ @ @ @ P P @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ P P P P @ @ P P @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P P P @ @ P P P P P P P P P P P P P P P P P P P P P P @ @ P P P P P P @ @ P P P P P P P P
in the chuck and
tighten the jaws.
Give the allen key
a short powerful
blow in an anti-
clockwise
direction with a
hammer to
depth stop until the distance between the end of the
depth stop and the end of the drill bit is equal to the
23
ENGLISH
To remove the
chuck, open the
jaws of the chuck
with the chuck
key. Hold the
chuck firmly in
one hand, and with
a screwdriver turn
the screw set in
@ @ @ @ @ @ @ @ @ @ @ @ @ @ P P @ @ P P @ @ P P @ @ P P P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ y y P P P P @ @ @ @ P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P @ @ @ @ @ @ @ @ P P @ @ P P P P P P P P @ @
Loosely locate
the handle on the
body of your drill.
Rotate the
handle around
the body of your
drill until it is in
the desired
Fit the drill bit.
@ @ @ @ @ @ @ P @ P @ @ P @ @ P P @ @ P @ @ @ P @ @ y P P @ @ P @ @ P P P @ P P P @ P P P @ P P P @ P P P P P P @ @ @ P @ P P @ P P P @ P @ @ @ P
Loosen the side
handle.
Slide the depth
stop until the end
of the depth stop
aligns with the
end of the drill
bit. Slide the
23
06-02-2001, 15:48