Flex CHE 5-45 SDS-max Notice D'instruction D'origine page 18

Switching on the power tool
 Press and hold down the switch.
Switch off the machine:
 Release the switch.
Safety clutch
`^rqflk>=
fÑ=íÜÉ=ë~ÑÉíó=ÅäìíÅÜ=íêáéëI=ëïáíÅÜ=çÑÑ=íÜÉ=éçïÉê=
íççä=áããÉÇá~íÉäó>
The safety clutch disconnects the motor from
the tool if a preset torque limit value is exceeded.
The insertion tool stops. As a result, the motor
and gears are protected from damage.
Operating instructions
`^rqflk>=
fÑ=íÜÉ=êÉÇ=iba=
çéÉê~íáçåI=ëïáíÅÜ=çÑÑ=íÜÉ=éçïÉê=íççä=áããÉÇá~J
íÉäó=~åÇ=éìää=çìí=íÜÉ=ã~áåë=éäìÖK=e~îÉ=ÉäÉÅíêáÅ=
éçïÉê=íççä=êÉé~áêÉÇ=Äó=ÅìëíçãÉê=ëÉêîáÅÉK
Hammer drilling
1. Move rotary knob for operating
mode to the
2. Insert drill bit.
3. Swivel the auxiliary handle into the required
position.
4. Set speed to the required value.
5. Insert mains plug.
The green LED
readiness) lights up.
18
EëÉêîáÅÉF=äáÖÜíë=ìé=ÇìêáåÖ=
symbol.
(operational
klqb>
fÑ=íÜÉ=iba=áë=åçí=äáí=ïÜÉå=íÜÉ=ã~áåë=éäìÖ=
áë áåëÉêíÉÇI=íÜÉ=éçïÉê=ÅçêÇ=çê=íÜÉ=Åçåíêçä=
ÉäÉÅíêçåáÅë=~êÉ=ÇÉÑÉÅíáîÉK=oÉãçîÉ=íÜÉ=éçïÉê=
ÅçêÇ=áããÉÇá~íÉäóK=e~îÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=
êÉé~áêÉÇ=Äó=ÅìëíçãÉê=ëÉêîáÅÉK
6. Grip electric power tool with both hands
and assume working position.
7. Position drill bit and switch on electric
power tool.
8. When hammer drilling, gently press electric
power tool forwards.
Excessive pressure does not reduce the
drilling time but the service life of the drill bit!
9. After drilling, switch off the power tool.
10. Pull out the mains plug.
Chiselling
1. Insert chisel.
2. Move rotary knob for operating
mode to the
3. Turn chisel into the required position.
4. Move rotary knob for operating mode
to the symbol.
5. Swivel the auxiliary handle into the required
position.
6. Set impact rate to the required value.
7. Insert mains plug.
The green LED
readiness) lights up.
klqb>
fÑ=íÜÉ=iba=áë=åçí=äáí=ïÜÉå=íÜÉ=ã~áåë=éäìÖ=
áë áåëÉêíÉÇI=íÜÉ=éçïÉê=ÅçêÇ=çê=íÜÉ=Åçåíêçä=
ÉäÉÅíêçåáÅë=~êÉ=ÇÉÑÉÅíáîÉK=oÉãçîÉ=íÜÉ=éçïÉê=
ÅçêÇ=áããÉÇá~íÉäóK=e~îÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=
êÉé~áêÉÇ=Äó=ÅìëíçãÉê=ëÉêîáÅÉK
8. Grip electric power tool with both hands
and assume working position.
9. Switching on the power tool.
10. When chiselling, gently press electric
power tool forwards to prevent it from
jumping.
11. After working, switch off the power tool.
12. Pull out the mains plug.
CHE 5–45 SDS-max
symbol.
(operational