Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
9. It is possible to remove the clamp assembly
(10) by loosening the clamp assembly lock
(11) and moving it to the other side of the
table. Make sure the clamp assembly lock is
tight before using the clamp.
10. Before turning on the saw, perform a dry
run of the cutting operation to check that
there are no problems.
11. Hold the operating handle (7) firmly and
squeeze the switch trigger (24). Allow the
blade to reach maximum speed.
12. Slowly lower the blade into and through
the workpiece.
13. Release the switch trigger (24) and allow
the saw blade to stop rotating before
raising the blade out of the workpiece.
Wait until the blade stops before removing
the workpiece.
Adjusting the laser lines
The lower laser is factory set to emit a laser
line along the right-hand side of the blade. The
upper laser is factory set to emit a laser line
to the left-hand side of the blade. This upper
laser can be adjusted by the operator to suit
blades of different kerf widths.
To adjust the position of the upper laser,
proceed
as follows:
1. Remove the laser cover by pulling it towards
you.
2. Switch on the laser lights with the on/off
switch (2).
3. Using a Phillips head screwdriver (not
supplied), adjust the position of the line from
the upper laser by turning the laser pitch
control (4).
4. Adjust until the left-hand laser line is aligned
with the left-hand side of the blade.
5. Switch off the laser lights.
GB
Using the laser line generator
WARNINGS.
Do not stare directly at the laser beam.
Never aim the beam at any person or an
object other than the workpiece.
Do not deliberately aim the beam at personnel
30
and ensure that it is not directed towards the
eye of a person for longer than 0.25s.
Always ensure the laser beam is aimed
at a sturdy workpiece without reflective
surfaces. Wood or rough coated surfaces are
acceptable. Bright shiny reflective surfaces
are not suitable for laser use as the reflective
surface could direct the beam back at
the operator.
Always remember to switch off the laser on/off
switch (2) after finishing a job. Only turn the
laser beam on when the workpiece is on the
miter saw table.
1. Mark the line of the cut on the workpiece.
2. Adjust the angle of miter and bevel of the
cut as required.
3. Switch on the laser light on/off switch (2).
4. Clamp the workpiece in position using the
laser lines to align the blade with the pencil
mark on the workpiece.
NOTE. To cut to the left-hand side of the
blade, align the left-hand laser line with the
pencil mark. To cut to the right-hand side of
the blade, align the right-hand laser line with
the pencil mark.
5. Plug in the machine and start the motor.
6. When the blade is at its maximum speed
(approximately 2 seconds), lower the blade
through the workpiece.
7. After completing the cut, switch off the laser
light on/off switch (2).
8. After each use, clean the laser light
assembly (1) as described below:
• Switch off the laser light switch (2) and
then remove the plug from the power
point.
• With the saw arm (5) in the raised
position, use a soft brush to dust
away the sawdust build-up around the
assembly.
NOTE. Wear eye protection whilst brushing
the dust away.
GUARANTEE
Maintenance and repair
Maintenance
Store the tool, instruction manual and
accessories in a secure place. In this way
you will always have all the information and
parts on hand.
Keep the tool's air vents unclogged and
clean at all times.
Remove dust and dirt regularly. Cleaning is
best done with compressed air or a rag.
Never use caustic agents to clean plastic parts.
Lubricate the guide roller from time to time
with a drop of oil. It will extend the life of
the roller.
CAUTION. Do not use cleaning agents
to clean the plastic parts of the tool.
A mild detergent on a damp cloth is
recommended. Water must never come
into contact with the tool.
General inspection
Regularly check that all the fixing screws are
tight. They may vibrate loose over time.
Guarantee
Thank you for investing in a Haussmann
power tool. These products have been made
to demanding, high quality standards and
are guaranteed for domestic use against
manufacturing faults for a period of
36 months from the date of purchase.
This guarantee does not affect your
statutory rights. In case of any malfunction
of your Haussmann tool (failure, missing
part, etc.), please contact one of our service
technician at our toll free service line at
1-888-267-7713 from 9 am to 9 pm,
Monday to Friday, Eastern time.
Normal wear and tear, including accessory
wear, is not covered under guarantee. The
product is guaranteed for 36 months if used
for normal trade purposes. Any guarantee is
invalid if the product has been overloaded
or subject to neglect, improper use or an
attempted repair other than by an authorised
agent. Heavy duty, daily professional or hire
usage are not guaranteed. Due to continuous
product improvement, we reserve the right
to change the product specification without
prior notice.
31
GB
Publicité
