Bosch GNB 18V-38 Professional Notice Originale page 20

20 | English
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting/Changing the Magazine (see figure A)
Insert the magazine (12) into the power tool and allow it to
engage.
To change the magazine, press the unlocking lever (11)
clockwise. Remove the magazine from the power tool with a
slight rotation.
Select nails suited to the intended application:
Designation Order number
NB‑16 1 600 A02 F4K
NB‑19 1 600 A02 F4L
NB‑25 1 600 A02 F4M
NB‑32 1 600 A02 F4N
NB‑38 1 600 A02 F4P
NK‑35 1 600 A02 F4R
NM‑13 1 600 A02 F4S
NM‑16 1 600 A02 F4T
NM‑19 1 600 A02 F4U
Filling the Magazine:
– If necessary, clean the magazine slider (14) and
magazine (12), e.g. with a paintbrush.
– Press the button (15) on the magazine slider (14) and
slide it towards the magazine opening until it engages.
– Push a suitable nail strip (22) into the magazine opening.
The standard magazine can be filled with maximum 2 nail
strips and the extended magazine (accessory) can be
filled with 4.
– Press the button (15) on the magazine slider (14) and
slide it forwards as far as it will go.
Note: If only 2 nails are contained in the magazine (12), the
contact element (17) can no longer be pressed and no dis-
charging procedure is triggered. Fill up the magazine.
Emptying the Magazine:
– Press the button (15) on the magazine slider (14) and
slide it towards the magazine opening until it engages.
– Rotate the magazine so that the nail strip (22) can slide
out of the magazine opening.
Removing/Changing the Contact Element
(see figure C)
The contact element (17) can be removed to be cleaned or
changed.
Remove the rechargeable battery (10). Empty the
magazine (12) and remove it.
1 609 92A 75W | (10.01.2023)
Filling/Emptying the Magazine (see figure B)
u
u
During any work on the magazine, hold the power tool in
such a manner that the outlet (18) is not pointed at your
body or at other persons.
Suitable for Length (mm) Diameter (mm)
Shank
Concrete 16 2.7
(smooth)
19
25
32
38
35 2.7
(knurled)
Steel 13 3
(graduated)
16
19
Pull the contact element release button (16) and remove the
contact element (17) from the power tool.
Push the cleaned or new contact element (17) into the
power tool until it engages.
Operation
Starting Operation
Switching On and Off
To switch on the power tool, press the on/off button (1) on
the user interface until the user interface lights up.
To switch off the power tool, press the on/off button (1)
again.
The power tool switches off automatically after 30 min if it is
not being used.
Checking the Suitability of the Substrate
Check the suitability of the substrate before loading the
power tool with nails or performing fastening.
The substrate must be level and free from residue.
To check the hardness of the substrate material, use a nail as
a centre punch. Use a hammer to hit it with a powerful strike
on the material. Check the result:
– The point of the nail is blunted: The substrate is too hard
Be careful when handling nails, especially when load-
ing and unloading. The nails have sharp points which
may result in personal injury.
Only use nails that have been recommended by Bosch
for your power tool. Using unapproved nails can damage
the power tool and cause injuries.
Material
Head
6.25 High-carbon
steel, elec-
trogalvanised
and not suitable; the nail may ricochet.
Nail strip col-
our
Blue
Black
Bosch Power Tools