Bosch GNB 18V-38 Professional Notice Originale page 18

18 | English
Never discharge a nail on top of another nail. This may
u
lead to the nail being deflected or the power tool reacting
unexpectedly.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is designed to put nails into hard materials
such as concrete (e.g. poured concrete, grouted joints) and
steel (e.g. structural steel, hot-rolled steel).
The power tool must not be used on very soft surfaces (e.g.
wood, lightweight construction materials) or very hard sur-
faces (e.g. high-strength steel). The power tool must also not
be used on the following substrates: Natural stone, vertical
mortar joints, hollow blocks, bricks, glazed brick, glass,
hardened steel, tool steel, spring steel, cast iron, weld
seams.
Check the suitability of the substrate before use (see
"Checking the Suitability of the Substrate", page 20).
The power tool is intended for hand-held use only.
The power tool is only intended for indoor use.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off button (user interface)
(2) Power tool status indicator (user interface)
(3) Battery charge indicator (user interface)
(4) Reset button (user interface)
(5) Unlocking switch for trigger
(6) Trigger
(7) Handle (insulated gripping surface)
(8) User Interface
(9) Rechargeable battery release button
a)
(10) Rechargeable battery
(11) Magazine release lever
(12) Magazine
(13) Supporting leg
(14) Magazine slider
(15) Magazine slider button
(16) Contact element release button
(17) Contact element
(18) Outlet
(19) Worklight
1 609 92A 75W | (10.01.2023)
(20) Depth stop switch
(21) Punch pin
(22) Nail strip
(23) Utility hook
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless nailer
Article number
Rated voltage
Actuation mode
Max. insertion frequency
(with battery ≥ 4 Ah)
Fastener
– Type
– Length
– Shank diameter
Standard magazine capacity
Dimensions without re-
chargeable battery
(length × width × height)
Weight according to EPTA-
Procedure 01:2014
Weight without battery
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
Permitted ambient temperat-
ure during storage
Compatible rechargeable
batteries
Recommended rechargeable
batteries for maximum per-
formance
Recommended chargers
a)
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
Noise/Vibration Information
Noise emission values determined according
to EN 60745‑2‑16.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85 dB(A); sound power
level 96 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
a)
GNB 18V‑38
3 601 JL7 0..
V=
Full sequential
−1
s
mm
mm
Nails
mm 405 × 138 × 309
kg
kg
°C
°C
B)
°C –20 to +50
GBA 18V...
ProCORE18V...
ProCORE18V...
Bosch Power Tools
18
2
Nail
13–38
2.7–3
22
A)
4.4–5.4
4.1
0 to +35
–5 to +50
≥ 4 Ah
GAL 18...
GAX 18V...
GAL 36...