Publicité
Les langues disponibles
Les langues disponibles
90565611 PCL120CR Lithium Recip Saw.qxd:??????-00 Cir Saw book
• When cutting pipe or conduit ensure that they are free from water, electrical wiring, etc.
• Do not touch the workpiece or the blade immediately after operating the tool.
They can become very hot.
• Do not use in rain or wet conditions.
WARNING:
ALWAYS use safety glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CPA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NOSH/OSHA respiratory protection.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the state of California to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
WARNING:
Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face
and body.
WARNING:
Always wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise
from this product may contribute to hearing loss.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially haz ard ous situation which, if not avoided, may
result in minor or mod er ate injury.
CAUTION:
Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
Symbols
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V..................volts
Hz................hertz
min ..............minutes
............direct current
................Class I Construction
(grounded)
................Class II Construction
(double insulated)
All manuals and user guides at all-guides.com
A ..................amperes
W..................watts
................alternating current
n o ................no load speed
..................earthing terminal
................safety alert symbol
.../min or rpm ....revolutions or reciprocation
per minute
4
6/9/10
2:48 PM
Page 4
• When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the correct size
to use depending on cord length and nameplate ampere rating. If in doubt, use the
next heavier gage. The smaller the gage number, the heavier the cord.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft.
50 ft.
75 ft.
7.6 m
15.2 m
22.9 m
Wire Size AWG
18
18
FUNCTIONAL DESCRIPTION
Figure A
1. On/off switch
2. Lock-off button
3. Pivot release slider
4. Shoe
5. LED Work light
6. Adjusting shoe
7. Shoe adjustment
screw
8. Blade clamp collar
9. Allen wrench / holder
10. Battery
11. Battery release button
12. Charger
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS
SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for
battery chargers.
• Before using charger, read all instructions and cautionary markings on charger, battery
pack, and product using battery pack.
WARNING:
Shock hazard. Do not allow any liquid to get inside charger.
CAUTION:
Burn hazard. To reduce the risk of injury, charge only designated
PORTER-CABLE batteries. Other types of batteries may burst causing personal injury
and damage.
CAUTION:
Under certain conditions, with the charger plugged in to the power
supply, the charger can be shorted by foreign material. Foreign materials of a conductive
nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic
particles should be kept away from charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity. Unplug charger before
attempting to clean.
• DO NOT attempt to charge the battery pack with any chargers other than the
ones in this manual. The charger and battery pack are specifically designed to work
together.
100 ft.
125 ft.
150 ft.
30.5 m
38.1 m
45.7 m
16
16
14
14
6
7
8
A
9
2
5
1
4
11
10
11
12
5
175 ft.
53.3 m
12
3
10
Publicité
