Fm Mode - PERFECTPRO WORKTUBE DAB+ Manuel De L'utilisateur

3. When DAB stations in the tuned channel are found, the display will show the name of the station. Any new radio stations found
will be added to the list stored in the radio.
4. The signal strength display shows the reception of the station. The clear unfilled rectangle indicates minimum signal level
required for satisfactory reception. The signal strength bars will go up or down showing the changing signal strength as you
adjust the antenna or the radio position.
5. Repeat step 1 to 4 for other channels with new stations.
6. Press the MENU button twice to exit manual tuning and return to normal DAB operation.
Dynamic Range Control (DRC) settings – DAB
DRC can make quieter sounds easier to hear when your radio is used in a noisy environment.
1. In DAB mode, press the MENU button and the TUNING ◄◄ or ►► buttons until the display shows "DRC Value", then press
the SELECT-INFO button .
2. Press the TUNING ◄◄ or ►► buttons to select required DRC setting (default is OFF).
DRC off DRC is switched off, broadcast DRC will be ignored.
DRC high DRC is set as sent by broadcaster.
DRC low DRC level is set to 1/2 that sent by broadcaster.
3. Press the SELECT-INFO the knob to confirm the setting. The display will return to normal radio display.
Note: Not all DAB broadcasts are able to use the DRC function. If the broadcast does not support DRC, then the DRC setting in the
radio will have no effect.
Prune stations – DAB
If you move to a different part of the country, some of the stations that were listed may no longer be available. Also, from time to
time, some DAB services may stop broadcasting, or may change location or frequency. The Prune stations function will delete the
unavailable DAB stations from your station list.
1. In DAB mode, press the MENU button and the TUNING ◄◄ or ►► buttons until the display shows "Prune", then press the
SELECT-INFO button.
2. Press the TUNING ◄◄ or ►► buttons to select between "Yes" or "No" (default is No). Select "Yes" to enable this function if
required, otherwise, select "No".
11
3. Press the SELECT-INFO button to confirm your setting. The display will return to last menu and press MENU to go to the
normal radio display.
Note: If you have moved the radio to a different part of the country, you should also carry out a search for new stations (please see
the section "Finding new stations – DAB").

FM MODE

Operating the radio – FM seek station
1. Press the On/Off button to switch on the radio.
2. Select the FM RADIO waveband by pressing the SOURCE button.
3. If this is the first time to switch to FM mode, the station in preset 1 will be played. If the radio has been used before, the last
listened station will be played.
4. To seek station, press the TUNING ◄◄ or ►► buttons. The scan stops automatically when it finds a station of sufficient
strength.
5. After a few seconds, the display will update and show station name if RDS information is being received.
6. To find other stations, press the TUNING ◄◄ or ►► buttons again.
7. To seek station in an opposite direction, press the TUNING ►►button to scan from low frequency to high frequency or press
the TUNING ◄◄ button to scan from high frequency to low frequency.
8. When the waveband end is reached, the radio will recommence tuning from the opposite waveband end.
Manual tuning – FM
1. Press the On/Off button to switch on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Press the TUNING ◄◄ or ►► buttons to reach the required FM station. The radio will change the frequency in steps of 50
kHz.
4. Adjust the rubber antenna to get the best reception. If the radio is tuned to a station of sufficient signal strength with RDS
information present, the display may change to show the station name.
5. When the waveband end is reached, the radio will recommence tuning from the opposite waveband end.
GB GB
12