Falcon Toledo XT Instructions D'utilisation Et D'installation page 50

WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
RH oven
Remove the two fi xings that secure the thermostat phial
cover. Unclip the thermostat phial from the clips in the oven
back panel.
LH oven
Remove the two screws holding the thermostat phial to
the oven fan cover at the rear of the oven. Pull the unit
forward to access the rear of the cooker. Remove the both
cover boxes by removing the fi xing screws and lifting clear.
Feed the thermostat capillary clear of the oven. Disconnect
the wires from the thermostat and undo the two fi xings
that secure the control to the mounting plate. Fit the
replacement and re-assemble in reverse order. Ensure that
the phial is clipped to the oven rear, positioned centrally
between the clips.
Check that the thermostat functions correctly.
7 To Remove an Oven element Thermal Cut-Out.
Disconnect from the electricity supply.
Pull the cooker for ward to gain access to the cover box.
Undo the cover screws and lift clear. The cutout is located
on the earth plate be side the oven element con nec tions.
Disconnect the cutout wir ing. Undo the fi xings that secure
the cutout to the earth plate and re move. Fit re place ment
control and re-as sem ble in reverse order.
8. To Change Hotplate Control Taps
Remove the Control Panel (see 1). Lift up the appropriate
hotplate tray front (see 2).
Unplug the FSD lead from the rear of the tap. Undo
compression fi tting at the rear of the tap. Remove the
fi xings that secure the tap to the gas rail. Remove the tap.
Remove and discard the gasket seal. Fit new gasket seal to
replacement tap. Re-assemble in reverse order. Check the
appliance is gas sound. Check hotplate ignition.
9. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new
injector. Reassemble in reverse order. Check appliance is gas
sound.
10. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically up
suffi ciently to grip the lead between thumb and forefi nger.
Pull off the electrode, but keep hold of the lead. Fit new
electrode to the lead. Fix electrode in burner with screw.
Replace burner cap. Check the burner ignition. Replace pan
supports.
11. To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
LH hotplate burners
Remove heat shield (2 screws). The burners are mounted
in 2's on cross supports. Disconnect the burner feed pipes
at the burners. Remove the screw on the right holding
the cross support. Slide the support to the right to release
in from the left hand location. Lift the cross support and
burners clear. The burners are fi xed to the cross supports
with 2 screws. Remove the appropriate burner and fi t
the new one. Reassemble in reverse order. Check burner
operation is satisfactory.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check burner
operation is satisfactory.
12. To Remove an Oven Door
Open oven door. Support the door and remove the two
screws securing the upper hinge and gasket to the cooker
front. Remove the door from the lower hinge by lifting
slightly and moving outwards.
Reassemble in reverse order.
13. To Change Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel
fi xing screws from the door sides (two each side).
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2 retaining
nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
50