Publicité
Les langues disponibles
Les langues disponibles
Connecting a TV and playback
components
HDMI/DVI-compatible TV
HDMI/DVI-compatible
Blu-ray DIsc player
HDMI OUT
DIGITAL OUT
OPTICAL
OUT 1
IN
1
BD IN
(CONTROL)
IN
( DVD )
HDMI
OUT 2
OUT 1
IN
1
BD IN
IN
2
IN
3
IN
4
IN /MHL
6
LAN
(10/100)
(HDZONE)
(CONTROL)
DC OUTPUT
for WIRELESS LAN
ASSIGNABLE
1 6
-
(
(
(DVD)
(SAT/CBL)
OUTPUT 5 V
OUTPUT 5 V
SELECTABLE
0.9 A MAX
)
0.6 A MAX
)
IN
• If the TV does not support the HDMI Audio Return Channel
function, optical digital cable (
) connection is required to
A
listen to the TV sound over the receiver.
• If the TV supports the HDMI Audio Return Channel
function, the sound of the TV is input to the receiver via the
HDMI terminal, so there is no need to connect an optical
). In this case, set ARC at HDMI Setup
digital cable (
A
to ON. For details, see "HDMI Setup" of the operating
instructions.
• Please refer to the TV's operation manual for directions on
connections and setup for the TV.
• With factory default settings, video from the video cable
or component cable will not be output from the HDMI
terminal. To output video, you must switch video input to
the device connected with the video cable or component
cable and set V.CONV to ON. For details, see "Setting the
Video options" of the operating instructions.
Connecting antennas
1
HDMI IN
A
OPTICAL
AM LOOP
1
( TV )
ASSIGNABLE
FM UNBAL
75
ANTENNA
Note
OPTICAL
1
(TV)
ASSIGNABLE
• Refer to the operating instructions in the included CD-
ROM if you wish to connect a TV or playback component
in a method other than an HDMI connection.
• Refer to the operating instructions in the included CD-
ROM for other device connections.
Plugging in the receiver
Only plug in after you have connected all your components to
this receiver, including the speakers.
CAUTION
• Handle the power cord by the plug part. Do not pull out
the plug by tugging the cord, and never touch the power
cord when your hands are wet, as this could cause a short
2
AM loop antenna
AM LOOP
FM UNBAL
75
ANTENNA
FM wire antenna
Connecting up (continued)
circuit or electric shock. Do not place the unit, a piece of
furniture, or other object on the power cord or pinch the
cord in any other way. Never make a knot in the cord or tie
it with other cables. The power cords should be routed so
that they are not likely to be stepped on. A damaged power
cord can cause a fire or give you an electric shock. Check
the power cord once in a while. If you find it damaged,
ask your nearest Pioneer authorized independent service
company for a replacement.
• Do not use any power cord other than the one supplied
with this unit.
• Do not use the supplied power cord for any purpose other
than that described below.
• The receiver should be disconnected by removing the
mains plug from the wall socket when not in regular use,
e.g., when on vacation.
• Make sure the blue uSTANDBY/ON light has gone out
before unplugging.
1
Plug the supplied power cord into the AC IN
socket on the back of the receiver.
2
Plug the other end into a power outlet.
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 40 cm at top, 10 cm at rear, and 20 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
7
Publicité
