Publicité
Les langues disponibles
Les langues disponibles
1. PRECAUTIONS
Installation and handling precautions
(1) Opening the transport lock
• Make sure that the transport lock is released and all trans-
port protective materials are removed before turning on the
power. Failure to do so will result in equipment malfunction.
(2) Location of installation
• Do not install the equipment near a source of vibration such
as motor, engine or loudspeaker. They may adversely af-
fect the equipment performance.
• Do not install the equipment in a place that is exposed to
radiation, X-rays or corrosive gases. This may cause a mal-
function or failure of the equipment.
• If the equipment is to have a fixed installation, we advise
you to give sufficient allowance for space so that extension
and replacement of optional units and other operations such
as replacement and maintenance can be easily performed.
For details, please consult your dealer or nearest JVC-au-
thorized service agent.
• This equipment must be installed on a level surface that is
subject to minimal vibration
(3) Condensation
• If the equipment which has been left in a cold room for a
long period of time and is moved to a warm room or if the
temperature of the room suddenly increases, condensation
may occur on a mobile part, optical pickup or a disc inside
the equipment with a disabling effect. If this occurs, do not
use the equipment for a few hours before starting it again.
(4) Interference with reception of other devices
• When this equipment is used near a radio receiver such as
a radio, television or BS tuner, reception of radio waves on
these these devices may experience interference.
(5) Use in a strong radio wave environment
The equipment may not function properly if it is used in a
strong radio wave environment, for example near an illegal
radio station or a broadcasting station. If this happens, please
consult your dealer or nearest JVC-authorized service agent.
(6) Compatible media
Media compatible with the MC-8200U/8600U varies depend-
ing on the drive in which it is accommodated. For details,
refer to the instruction manual of the relevant drive.
Disc handling precautions
A disc is made of plastic material which can be easily dam-
aged. If the discs are damaged or become dirty, it may lead to
malfunction such as incorrect data readout. To prevent this han-
dle the discs with care so that they will stay free of damage,
stain, dust/dirt adhesion, warping, etc.
(1) Do not touch the reflective surface (data surface) of a
disc directly with your hand. Be sure to use special
care when handling double-sided discs.
(2) Use commercially available cleaning kits such as a CD
cleaner to remove dust and/or dirt from the disc sur-
face.
• Gently wipe-clean the disc surface without scratching it.
(Make sure to wipe from the centre of the disc towards the
outer edge. Never use a circular motion.)
(7) Installation environment
• This equipment has been designed with consideration for
• If the equipment is used outside of the suitable temperature
(8) Backup
• JVC cannot accept responsibility for any loss of data and/or
• When this equipment is used with a system which runs con-
(9) Never take the equipment apart.
• Fire and electric shock may result. Do not try to take apart
(10) Cleaning
• Do not use solvents (paint thinner, benzene, etc.), cleaning
• Wipe-clean using a well-squeezed cloth which has been
(11) Do not place anything on the top panel.
• Do not place any objects on or step onto the top panel of
(3) Do not use chemicals for disc cleaning.
• Never use any solvents other than those included in the
• Never use analogue record cleaning fluid, benzene, alcohol
(4) Do not damage the label surface
• Damage to the label surface also affects the data surface
• Do not attach pieces of paper or adhesive tape to either
• When you need to write on the label surface, please use a
(5) Periodical cleaning of the discs is recommended.
• Periodical disc cleaning may be required depending on the
* Always from the centre to outer edge
dust protection, but its structure is not dust-proof. There-
fore, if it is used in an environment where cigarette smoke
and/or dust are present, the lens of the drive or a disc will
become dirty and stop functioning correctly. Using the equip-
ment in these conditions should be avoided. If, however, you
have to use it in a dusty environment, make sure to carry
out 'maintenance & regular inspection' at an earlier interval.
and humidity range, the drive life may become greatly short-
ened. Please make sure to use the equipment in an appro-
priate environment.
any other direct and indirect damage caused by the use or
malfunctioning of this equipment. We therefore strongly ad-
vise that all important data should be fully backed up in case
of unexpected loss.
tinually for 24 hours or which cannot be turned off at all, we
recommend a redundancy design such as [a] back-up sys-
tem on the system.
or modify this equipment or the drive units inside.
products containing abrasives, anti-static agent, cloth soaked
in detergent and silicon cloth. They can cause discolora-
tion.
soaked in a neutral detergent.
this equipment as a malfunction or accident may result.
cleaning kits.
or anti-static agent.
immediately underneath it.
side of the disc.
permanent ink felt-tip pen.
Writing implements with hard tips such as ball-point pens
and pencils should not be used as they will damage the
surface.
equipment installation environment and disc handling
method.
E5
Publicité
