ubbink NorthWood 580 Notice De Montage page 17

SUMMARY:
- Preparing the ground
- Erecting the sides of the pool
- Screwing in the brackets
- Putting up the supports for the sides of
the pool
- Preparing the sides of the pool
- Installing the felt underlay and the
liner
- Cutting out the liner to it the
backwash inlet nozzle and the skimmer
- Assembly of the pine edging
9 - The ladders
3a - Mark in the pre-drilling points on the 7 complete planks.
3b - Mark in the pre-drilling points on the on the plank for the skimmer.
3c - Position the brackets.
3d - Make the brackets level and screw them in so that the screw heads are completely embedded into the wood.
3e - Secure the wooden stops for the skimmer trap doors
4a - Mark the position of the holes and arrange the posts. Cut the wall reinforcement posts (cross-section 45x135) to the height of the swimming pool.
4b - Drill the sides of the pool.
4c - Screw all planks and countersink all screw heads into the wood.
5a - Screw in the skimmer intake in the upper plank using two screws provided in the skimmer box.
5b - Install the outer skimmer seal and the skimmer itelf.
5c - Secure the whole unit tightening it really well to ensure it is completely waterproof.
5d - Once you have put Telon tape round the fed through unit, screw the fed through stop valve into the body of the skimmer. Shut off the valve.
5e - Drill the tracks according to the measurements (3 cm from the ends and then approximately every 20 cm).
5f - Unroll the wall felt and press the plastic rail on top, lush with the upper plank.
5g - Screw in the irst track of the liner.
5h - Mark out where the corner cut is to be made.
5i - Cut the corners according to the diagram.
5j - Feel where the outside frame of the skimmer is.
5k - Cut out the felting around the outer edge of the skimmer.
5l - Do the same with the backlow inlet nozzle.
5m - Put in one of the skimmer seals.
5n - Put in the backlow inlet nozzle seal. It must make contact with the wood. Therefore cut out the felting
6a - Put the ground protection in place.
6b - Cut out the protective felting using a Stanley knife or a pair of scissors.
6c - Put the liner in place.
6d - Fit the corners of the liner into the corners of the pool.
6e - Hook the liner on to the lip of the track.
6f - Check the position of the liner and smooth out the biggest creases.
6g - Adjust the corners of the liner to it the frame of the pool.
6h - Fill the pool with water to a level of 2 cm.
6i - Smooth out the creases.
6j - Resume illing with water
7a - Stop illing when the water is just below the backlow inlet nozzle.
7b - Position the backlow inlet nozzle from the inside of the pool.
7c - Cut out the liner for the backlow inlet nozzle, leaving about 2 mm play around it.
7d - Tighten the nut on the backlow inlet pipe enough to make sure it is waterproof.
7e - Bind the fed through ends of the ittings with Telon tape, working in an anti-clockwise direction. Wrap round at least 20 times.
7f - Screw one of the ends to the backlow inlet nozzle and the other one to the skimmer.
7g - Install one of the pipes to the backlow inlet nozzle and secure it using a metal collar.
7h - Put the other end of the pipe into the swimming pool and resume illing with water.
7i - Mark in the position of the skimmer seal.
7j - Put in the skimmer seal and the frame.
7k - Cut out the liner in the inside of the skimmer frame. Then place and clip in the cover lange.
7l - When the water is halfway up the skimmer, it is at the correct level (after you have put the ilter in place).
7m - Cut off the inishing proiles at the height of the swimming pool, making sure to leave 2cm clearance between the end of the inishing proile and the
edging.
8
• (see page 31-32)
9 The ladders should not be used for any other purpose
The maximum weight limit is 150 kg
The means of access should be put in a safe place when not in use
9a - Make the ladder level. To do that lush out the air under the steps if necessary.
9b - Secure the stainless steel supports using the bolts provided in the stainless steel ladder box.
NOTICE 580 - H130-2015_2.indd 18
1a - Pour a concrete slab to the dimensions speciied on page 21, of a minimum thickness of 10cm
1b - Swimming pool should be oriented so that the skimmer inlet faces the prevailing wind, in order to optimise
surface particle iltration. For this, use temporarily the irst row of planks.
1c - Mark the position of the structure on the ground, keeping a 50cm margin to make controlling the shape
easier.
For the warranty to be valid, a concrete slab must be in place.
2* - IMPORTANT: It is important that the planks are correctly interlocked, especially those at the bottom
(where the pressure of the water will be greatest).
TO INTERLOCK A WARPED PLANK:
Even if they are on a pallet and wrapped in packaging, it is possible that some planks may be warped.
This is entirely normal in view of the fact that wood is a living material.
In order to install a warped plank, engage one of the two sides of the plank in position. Straighten the
other side using 2 wooden wedges and the clamp. Use the hammer and the sacriice piece to engage it in
position.
2a - Assembly principle. Use the sacriice part for itting together all the planks.
2b - Make the irst row of planks level.
2c - Control the shape using a tape measure (10m).
2d - Control the shape using a tape measure (10m).
2e - Position the water jet plank on the 7th row. This can be either to the right or the left of the skimmer.
2f - Position the lower skimmer plank on the 8th row after the lower half plank.
2g - Position the upper skimmer plank and the three top planks.
If using a safety tarpaulin, make sure to centre
the stainless steel ladder on the edging
17
07.12.15 12:52