DWT WS06-115 Notice Originale page 22

7 Body
8 Speed selector thumbwheel
9 Wrench *
10 Flange wrench *
11 Cap *
12 Mounting lug
13 Screw
14 Fixing screw
15 Spindle
16 Flange
17 Disc *
18 Clamping nut
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation
of power tool elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Additional handle (see fig. 1)
Always use the additional handle 5 when operating�
Additional handle 5 may be positioned as deemed
comfortable by the user�
• Release additional handle 5 as shown on fig. 1.
• Extract cap 11 and screw additional handle 5 into
the threaded opening�
• Insert cap 11 into the freed threaded opening�
Protective casing
Always use protective casing 4 when
applying cutting and grinding discs.
Operation
accessories without protective casing 4
is strictly forbidden. Protective casing 4 should al-
ways face the operator with its closed part.
Mounting / dismounting the protective casing (see
fig. 2)
[WS07-115, WS07-125,
WS08-115 V, WS08-125 V]
• With a screwdriver (not supplied with the power tool)
release screw 13 and install protective casing 4 onto
the spindle neck, watching that mounting lug 12 comes
into the longitudinal groove of the spindle neck (see
fig. 2).
• Turn protective casing 4 into the required position
and tighten screw 13 with a screwdriver (not supplied
with the power tool)�
• When dismounting protective casing 4 repeat the
aforementioned operations in reverse order�
of the aforementioned
WS08-115, WS08-125,
Автотовары «130»
Adjusting the protective casing into work position
(see. fig. 3)
[WS06-115]
This model is supplied with the mounted protective
casing 4� Before proceeding to establish a protective
casing 4, so that its closed part facing toward the user�
• With a screwdriver (not supplied with the power tool)
release fixing screw 14 (see fig. 3).
• Turn the protective casing 4 into the required posi-
tion and tighten the fixing screw 14 with a screwdriver
(not supplied)�
Mounting / replacement of accessories
After mounting accessories of any kind,
make a trial run before commencing op-
eration - start the power tool and let it
work in idle mode for not less than 30
seconds. The operation of accessories with radial
or axial run-out and causing increased vibration of
the power tool is strictly forbidden.
Wearing protective gloves is recom-
mended for mounting / replacing acces-
sories.
Mounting of cutting / grinding disc (see fig. 4)
• Install flange 16 onto spindle 15 (see fig. 4).
• Install one of the aforementioned accessories onto
spindle 15�
• Press and hold spindle lock 2�
• Screw clamping nut 18 onto spindle 15 and tight-
en it with flange wrench 10� Attention: at mounting
any accessories over 4 mm thick clamping nut 18
should be turned over (see fig. 4).
• Release spindle lock 2�
Replacing the cutting / grinding disc (see fig. 4-5)
• Press and hold spindle lock 2�
• Release clamping nut 18 with flange wrench 10 (see
fig.5).
• Replace the accessory�
• Screw clamping nut 18 onto spindle 15 and tight-
en it with flange wrench 10� Attention: at mounting
any accessories over 4 mm thick clamping nut 18
should be turned over (see fig. 4).
• Release spindle lock 2�
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
Switching on:
Press the back part of on / off switch 6 and while
holding it in this position, move on / off switch 6
forward� Press the front part of on / off switch 6 to fix it
in pressed position�
English
21
Initial operating
of the power tool
tool on / off