Makita LS0714 Manuel D'instructions page 16

Adjusting the miter angle (Fig. 11)
Loosen the grip by turning counterclockwise. Turn the
turn base while pressing down the lock lever. When you
have moved the grip to the position where the pointer
points to the desired angle on the miter scale, securely
tighten the grip clockwise.
CAUTION:
• When turning the turn base, be sure to raise the handle
fully.
• After changing the miter angle, always secure the turn
base by tightening the grip firmly.
Adjusting the bevel angle (Fig. 12 & 13)
To adjust the bevel angle, loosen the lever at the rear of
the tool counterclockwise.
Push the handle to the left to tilt the saw blade until the
pointer points to the desired angle on the bevel scale.
Then tighten the lever clockwise firmly to secure the arm.
To tilt the blade to the right, push the release button at
the rear of the tool while tilting the blade slightly to the left
after loosening the lever. With the release button
depressed, tilt the saw blade to the right.
CAUTION:
• When tilting the saw blade, be sure to raise the handle
fully.
• After changing the bevel angle, always secure the arm
by tightening the lever clockwise.
• When changing bevel angles, be sure to position the
kerf boards appropriately as explained in the "Position-
ing kerf board" section.
Adjusting the lever position (Fig. 14)
The lever can be repositioned at every angle 30° when
the lever does not provide full tightening.
Loosen and remove the screw that secures the lever at
the rear of the tool. Remove the lever and install it again
so that it is slightly above the level. Secure the lever with
the screw firmly.
Switch action
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
• When not using the tool, remove the lock-off button and
store it in a secure place. This prevents unauthorized
operation.
• Do not pull the switch trigger hard without pressing in
the lock-off button. This can cause switch breakage.
For European countries (Fig. 15)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push the lever to the left, press in the lock-off button and
then pull the switch trigger. Release the switch trigger to
stop.
For all countries other than European countries
(Fig. 16)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
16
All manuals and user guides at all-guides.com
WARNING:
• NEVER use tool without a fully operative switch trigger.
• For your safety, this tool is equipped with a lock-off but-
• NEVER tape down or defeat purpose and function of
Lighting up the lamps (Fig. 17)
For model LS0714F, LS0714FL
CAUTION:
• This is not a rainproof light. Do not wash the light in
• Do not touch the lens of the light, as it is very hot while
• Do not apply impact to the light, which may cause dam-
• Do not keep casting the beam of the light to your eyes.
• Do not cover the light with clothes, carton, cardboard or
Push the upper position of the switch for turning on the
light and the lower position for off.
Move the light to shift an area of lighting.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
Laser beam action (Fig. 18 & 19)
For model LS0714FL, LS0714L
CAUTION:
• Never look into the laser beam. Direct laser beam may
• LASER RADIATION, DO NOT STARE INTO THE
To turn on the laser beam, press the upper position (I) of
the switch. Press the lower position (O) to turn off.
Laser line can be shifted to either the left or right side of
the saw blade by adjusting the adjusting screw as fol-
lows.
1.
2.
3.
Laser line is factory adjusted so that it is positioned within
1 mm from the side surface of the blade (cutting posi-
tion).
NOTE:
• When laser line is dim and almost or entirely invisible
Any tool with an inoperative switch is HIGHLY DAN-
GEROUS and must be repaired before further usage.
ton which prevents the tool from unintended starting.
NEVER use the tool if it runs when you simply pull the
switch trigger without pressing the lock-off button.
Return tool to a Makita service center for proper repairs
BEFORE further usage.
lock-off button.
water or use it in a rain or a wet area. Such a conduct
can cause an electric shock and fume.
it is lighted or shortly after it is turned off. This may
cause a burn to a human body.
age or shorted service time to it.
This can cause your eyes to be hurt.
similar objects while it is lighted, which can cause a fire
or an ignition.
careful not to scratch the lens of light, or it may lower
the illumination.
injure your eyes.
BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRU-
MENTS, CLASS 2M LASER PRODUCT.
Loosen the adjusting screw by turning it counter-
clockwise.
With the adjusting screw loosened, slide the adjust-
ing screw to the right or left as far as it goes.
Tighten the adjusting screw firmly at the position
where it stops sliding.
because of the direct sunlight in the indoor or outdoor
window-by work, relocate the work area to a place not
exposed to the direct sunlight.