Makita LS0714 Manuel D'instructions page 13

ENGLISH
(Original instructions)
1 Stopper pin
2 Bolt
3 Adjusting bolt
4 Blade guard A
5 Thumb screw
6 Kerf board
7 Saw blade
8 Blade teeth
9 Left bevel cut
10 Straight cut
11 Turn base
12 Guide fence
13 Top surface of turn table
14 Periphery of blade
15 Adjusting screw
16 Stopper arm
17 Lock lever
18 Miter scale
19 Pointer
20 Grip
21 Lever
22 Release button
23 Bevel scale
24 Arm
25 Screw
26 Lock-off button
27 Switch trigger
28 Handle
29 Light
30 Light switch
31 Switch for laser
32 Wrench holder
33 Pipe holder
SPECIFICATIONS
Model
Blade diameter ................................................................................................................................................... 190 mm
Hole (arbor) diameter ............................................................................................................................................ 20 mm
Max. Miter angle .................................................................................................................................. Left 47°, Right 57°
Max. Bevel angle ................................................................................................................................... Left 45°, Right 5°
Max. Cutting capacities (H x W) with blade 190 mm in diameter.
Miter angle
0°
45° (left and right)
57° (right)
(Note)
* mark indicates that a wood facing with the following thickness is used.
1: When using a wood facing 20 mm thick.
2: When using a wood facing 15 mm thick.
3: When using a wood facing 10 mm thick.
All manuals and user guides at all-guides.com
Explanation of general view
34 Center cover
35 Socket wrench
36 Hex bolt
37 Safety cover
38 Shaft lock
39 Arrow
40 Blade case
41 Hex bolt (left-handed)
42 Outer flange
43 Inner flange
44 Spindle
45 Dust bag
46 Dust nozzle
47 Fastener
48 Support
49 Vise arm
50 Vise rod
51 Holder
52 Holder assembly
(optional accessory)
53 Vise knob
54 Projection
55 Vise shaft
56 Base
57 Rod 12
58 Two clamping screws which
secure the slide pole
59 Two clamping screws which
secure the slide pole
60 Vise
61 Spacer block
62 Aluminum extrusion
63 Over 15 mm
45° (left)
*45 mm x 265 mm (Note 1)
40 mm x 300 mm
*45 mm x 185 mm (Note 2)
40 mm x 212 mm
—
64 Over 420 mm
65 Holes
66 Set plate
67 Cut grooves with blade
68 Triangular rule
69 Arm holder
70 0 degree bevel angle adjusting
bolt
71 Left 45 degrees bevel angle
adjusting bolt
72 Work piece
73 Cutting line
74 Vertical vise
75 Pull out
76 Push
77 Lamp box
78 Screws
79 Fluorescent tube
80 Screwdriver
81 Screw (one piece only)
82 Lens for the laser light
83 Limit mark
84 Brush holder cap
85 Blade guard B (For European
countries)
86 Dust box
87 Cover
88 Button
89 Cylinder part
90 Sawdust
91 Blade guard
LS0714/LS0714F/LS0714FL/LS0714L
Bevel angle
0°
*60 mm x 265 mm (Note 1)
52 mm x 300 mm
*60 mm x 185 mm (Note 2)
52 mm x 212 mm
*60 mm x 145 mm (Note 3)
52 mm x 163 mm
5° (right)
—
40 mm x 300 mm
—
—
—
13