Atlas Copco BCP BL-2L-I06 Information Sur La Sécurité page 4

Safety Information
We, Atlas Copco Industrial Technique AB, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your "Customer
Center" for handling.
FCC and ISED Compliance Statement
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This de-
vice may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 919 272 7837
Email: rodney.hill@us.atlascopco.com
4
http://
and selecting 'Tools' then 'Legis-
© Atlas Copco Industrial Technique AB - 9834 6065 00
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is
acceptable and such modification is considered to violate the
Compliance Statement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the follow-
ing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
ISED Compliance Statement:
This device complies with: CAN ICES-3 (B)/NMB-3(B)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromet-
tre le fonctionnement.
Conformity to North American Standards
3008099
BCP BL-2L-I06
Listed
Conforms to UL 62841-1 and
UL 62841-2-2 Std.
Certified to CSA C22.2 No.
62841-1 and CSA C22.2 No.
62841-2-2 Std.