Atlas Copco BCP BL-2L-I06 Information Sur La Sécurité page 3

BCP BL-2L-I06
Technical Data
Product Data
Motor voltage
Speed range
Torque range
Weight
Ambient Temperature
Operating temperature, charge
Operating temperature, discharge
Storage temperature
Charger Compatibility
Accessory
Multi-Charger, 18/36V
Battery Compatibility
Accessory
Battery, 18V (2Ah)
Battery, 18V (2,5Ah)
Battery, 18V (4Ah)
Battery, 18V (5Ah)
Charger Temperatures
Charger operating tempera-
ture
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rota-
tional direction after any event that can influence the tighten-
ing result. Examples of such events include but are not lim-
ited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures
or practices
• changing of operator
18 V
150 - 440 r/min
0.8 - 2.5 Nm (0.6 - 1.8 ft lb)
0.86 kg (1.89 lb)
+5 to +40 °C
(+41 to +104 °F)
0 to +40 °C
(+32 to +104 °F)
−20 to +40 °C
(−4 to +104 °F)
Article Number
4211 5424 85
Article nr.
4211 5500 11
4211 5500 12
4211 5500 21
4211 5500 22
+5 to +40 °C
(+41 to +104 °F)
© Atlas Copco Industrial Technique AB - 9834 6065 00
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair
of the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number,
see front page) is in conformity with the following Direc-
tive(s):
2006/42/EC (MD), 2011/65/EU (RoHS), 2014/30/EU
(EMC), 2015/863/EU (RoHS amendment)
Harmonized standards applied:
EN 55014:2017, EN 55014-2:2015, EN 62841-1:2015, EN
62841-2-2:2014 + AC:2015 EN 61000-6-2:2005, EN
61000-6-3:2007 + A1:2011
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Tech-
nique AB, SE-105 23 Stockholm Sweden
Stockholm, 1 December 2021
Carl von Schantz, Managing Director
Signature of issuer
Noise and Vibration Declaration Statement
• Sound pressure level <70 dB(A) , uncertainty dB(A), in
accordance with ISO15744.
• Sound power level dB(A) , uncertainty dB(A), in accor-
dance with ISO15744.
• Vibration total value <2.5 m/s
cordance with ISO28927-2.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
Safety Information
2 2
, uncertainty m/s , in ac-
3