V2 MR2 Mode D'emploi page 8

N° Flashing Time
1 01 sec.
2 02 sec.
3 03 sec.
4 04 sec.
5 05 sec.
6 06 sec.
7 07 sec.
8 08 sec.
9 09 sec.
10 10 sec.
11 11 sec.
12 12 sec.
13 13 sec.
14 14 sec.
15 15 sec.
16 30 sec.
5. Count the number of led L1 flashings corresponding to the
time you wish to set. Press the RX button P1 during the
wished flashing.
6. The sequence of flashings stops and led L1 goes off:
the receiver is ready to be used.
REMOTE RADIO LEARNING
(Personal Pass system only)
This procedure allows to memorize new transmitters by radio, in
sequence and without removing the receiver from the
installation.
The transmitter which allows to enable the programming by radio
must be memorized in advance.
The keys of all the transmitters saved in the memory via radio will
have the same logic as for those of the transmitter that enabled
programming.
Therefore, if the transmitter that activated programming
has key 1 saved only, the new transmitters can only be saved
using key 1.
1.
Press for at least 5 seconds the keys 1+2 or 1+3 of one
transmitter that is already saved
2. Release both keys
3. Press, within 5 seconds, the key of the new transmitter that
you intend to save
4. Release the key and repeat the procedure for the other keys
of the remote control or with other radio controls to be saved
- 8 - ENGLISH
N° Flashing Time
17 1 min.
18 1,5 min.
19 2 min.
20 2,5 min.
21 3 min.
22 3,5 min.
23 4 min.
24 4,5 min.
25 5 min.
26 5,5 min.
27 6 min.
28 6,5 min.
29 7 min.
30 7,5 min.
31 BISTABLE
SUBSITUTIVE TRANSMITTER
(Personal Pass system only)
The substitutive transmitter, generated only by means of
WINPPCL, allows to replace by radio a transmitter stored in the
receiver.
A single transmition with the specially programmed SUBSTITUTIVE
TX, nearby the receiver, replaces the transmitter code with the
new one without removing the receiver from the installation.
Three code substitutions are permitted, if transmitter TX A is
memorised, the options are:
TX B replaces TX A (TX A is no longer operative)
TX C replaces TX B (TX B-A is no longer operative)
TX D replaces TX C (TX C-B-A is no longer operative)
ROLLING CODE MODE
(Personal Pass system only)
The receiver manages the rolling code for the Personal Pass
system. This function is enabled by default.
Rolling code mode may be deactivated by WinPPCL or by using
the P1 programming button.
1.
Press and hold button P1: the LED turns on
2.
After 8 seconds the LED goes off, release the button
3. The led starts a sequence of flashing for 5 seconds:
g
Single flashings
g
Double flashings
g
Triple flashings
4. To modify the parameters press the P1 push-button within
5 seconds after the first flashing of the sequence; the led will
flash according to the new parameters.
5. After 8 seconds, the led turns off and the receiver moves
back to normal operation
PROGRAMMING LOCK
(Personal Pass system only)
The PROGRAMMING LOCK function can be done only by
means of WINPPCL. This function inhibits to programme again
the receiver, either with P1 key or by radio. The receiver can be
programmed again only by means of WINPPCL.
FULL CODE ERASING
To perform a full code erasing do the following:
1. Switch off the power supply of the control unit where the
MR2 receiver is connected.
2. By holding the key P1 of the receiver pressed, you will
reactivate the power supply.
The receiver LED goes on: release the P1 key
3. The memory spaces are empty and available for a new
programming: the first remote control to be memorised
determines the mode of operation; Royal or Personal Pass
To perform a partial code erasing the PROG2 portable
programmer is required.
ROLLING CODE disabled
ROLLING CODE enabled
ROLLING CODE enabled
+ cloned code erasing