V2 MR2 Mode D'emploi page 7

PROGRAMMING
NOTE: the first remote control to be memorised determines the
mode of operation; Royal or Personal Pass.
To change the operating mode, it is essential to perform a FULL
CODE ERASING and then memorise the new remote control.
CAUTION: If the receiver is configured in the Personal Pass
mode, to program the BISTABLE and TIMER functions it is
required the use of a PROG2 programmer and of a WINPPCL
software.
m
IMPORTANT: to memorize the code in the correct way
it is necessary to keep a minimum distance of 1,5 metres
between the transmitter and the receiver's antenna.
The self learning programming system enables the code
memorization and the setting of the following functioning modes:
MONOSTABLE: it activates the corresponding relay through the
time of TX transmission. When the transmission stops, the relay
goes automatically off.
BISTABLE: it activates the corresponding relay on the first TX
transmission. The relay goes off on the second transmission.
TIMER: the tx transmission activates the corresponding relay
which goes off after the set time (max 7,5 minutes).
SELECTION OF THE RECEIVER
CHANNEL
1. Press P1 push-button of the receiver: L1 led switches on.
2. Release the push-button, the led switches off and it sends out
a sequence of single flashings for 5 seconds: the number of
short flashings shows the selected channel.
3.
To select the further channels press and release the P1
push-button within 5 seconds, the led changes type of
flashing according to the following table:
SELECTED N°
CHANNEL IMPULSES P1
CHANNEL 1 1
CHANNEL 2 2
CHANNEL 3 3
CHANNEL 4 4
N° Flashing
1 2 3 4
•
•
•
•
PROGRAMMING OF THE MONOSTABLE
FUNCTION
WARNING: If the transmitter is ROYAL, before starting
programming, set the desired code on the transmitter.
Set the same code on all transmitters.
1. Select the channel of the receiver to be programmed
2.
Within 5 seconds, press and hold the button on the remote
control.
- if the remote control unit is a ROYAL version, the
procedure ends at point 3
- if the remote control unit is a PERSONAL PASS version, go to
point 4 and follow the procedure until the end of the
section
3.
The LED of the receiver goes off and goes on again for 5
seconds. After 5 second the led goes off: the receiver is ready
to be used
4. The led of the receiver goes out and goes on again: the code
has been memorised and the receiver remains standby for 5 s
with a new code to be memorised
5.
Memorise all the remote control units necessary
6. After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
PROGRAMMING OF THE BISTABLE
FUNCTION
(ROYAL system only)
WARNING: before starting programming, set the desired code
on the transmitter. Set the same code on all transmitters.
1.
Select the channel of the receiver to be programmed
2. Within 5 seconds, press and hold the button on the remote
control
3. The LED of the receiver goes off and then goes on again:
press the pushbutton P1 of the receiver within 5 sec
4.
Led starts a sequence of flashings at low speed
(1 flash per second)
5.
After the thirtieth flash the led L1 remains on for 5 seconds
6. Press and release the pushbutton P1 within 5 seconds
7. The LED goes off: the receiver is ready to be used
PROGRAMMING OF THE TIMER
FUNCTION
(ROYAL system only)
WARNING: before starting programming, set the desired code
on the transmitter. Set the same code on all transmitters.
1. Select the channel of the receiver to be programmed
2. Within 5 seconds, press and hold the button on the remote
control
3. The LED of the receiver goes off and then goes on again:
press the pushbutton P1 of the receiver within 5 seconds
4.
Led L1 starts a sequence of flashings at low speed (1 flash
per second). The number of flashing corresponds to the time
which can be set as shown in the table.
ENGLISH - 7 -