Virutex RA17 VB Mode D'emploi page 9

To easily position the joints in the grooves we recommend
the use of SILICON JOINT ROLLERS (ref. 1746158). (Fig. 15)
11. MAINTENANCE OF THE
BRUSHES AND COLLECTOR
Disconnect from the mains before ca-
rrying out any maintenance operations.
Remove the screws L (Fig. 9) that hold the side covers
N and detach them from each other.
Remove the brush-holder P (Fig. 10) with small screw-
driver O, using one of the brush-holder side tabs to
lever it out. Push back the end of spring Q. Keep it in
this position to extract the brush and replace it with a
new genuine Virutex brush. Re-insert the brush-holder,
ensuring that it is firmly positioned in the casing and that
each of the brushes exerts a small amount of pressure
on the collector.
Re-attach the covers N with the corresponding screws,
making sure that no wires get caught in the process.
It is advisable to leave the machine running for 15
minutes once the brushes have been changed.
If the collector burns or juts out, it should be serviced
by a VIRUTEX service technician.
Always keep the lead and plug in good working condition.
12. NOISE LEVEL
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-17 and EN 60745-1 and serve as a basis for com-
parison with other machines with similar applications.
The indicated vibration level has been determined for
the device's main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).
13. GUARANTEE
All of VIRUTEX portable electrical goods are guaranteed
All manuals and user guides at all-guides.com
for 12 months from the date of supply, excluding any
damage which is a result of incorrect use or of natural
wear and tear on the machine.
All repairs should be carried out by the official VIRUTEX
technical assistance service.
VIRUTEX reserves the right to modify its products
without prior notice.
F R A N Ç A I S
FRAISEUSE À RAINURES RA17 VB
1. INSTRUCTIONS DE SÉCURITÉ POUR LE
MANIEMENT DE LA FRAISEUSE A RAINURES
Lire attentivement la BROCHURE
D'INSTRUCTIONS GÉNÉRALES DE SÉ-
CURITÉ, jointe à la documentation de
la machine.
1. Avant de brancher la machine, s'assurer que la tension
d'alimentation correspond à celle indiquée sur la plaque
des caractéristiques.
2. Maintenir toujours les mains éloignées de la zone de
coupe, et prendre toujours la machine par les poignées.
3. Utiliser toujours des outils d'origine VIRUTEX. Ne
jamais utiliser d'outils défectueux ou en mauvais état.
4. Il est necessaire de travailler avec l'aspiration de
poussière pour éviter que la fraise se casse.
2. CARACTÉRISTIQUES TECHNIQUES
Puissance absorbée..................................630 W
Moteur..................................................50/60 Hz
Révolutions.......................................28.000/min
Pince porte-fraise....................................Ø: 6 mm
Poids machine............................................1,9 kg
Niveau de pression acoustique
continu équivalent pondéré A.............................86 dBA
Niveau de puissance acoustique A..........................97 dBA
Incertitude..............................................................K = 3 dbA
Porter une protection acoustique!
Valeurs totales des vibrations......................a
Incertitude............................................................K: 1,5 m/s
3. ÉQUIPEMENT STANDARD
A l'intérieur de la mallette de transport, vous trouverez
les éléments suivants (Fig. 1):
1.- Fraiseuse à rainures RA17 VB avec fraise carbure
aiguisée aux deux pointes.
-1
: <2,5 m/s
2
h
2
9