Bosch Climate 3000i Notice D'utilisation page 53

Cleaning position
To make cleaning easier, the louver can be brought into a special position
(depending on model).
▶ Press the Mode and Swing keys simultaneously for one second when
the unit is switched off.
▶ To exit the cleaning position: press and hold both keys again.
3.6.2 Changing over display and alarm buzzer (Mute Mode)
▶ To switch on or off the display at the indoor unit and the alarm buzzer:
press LED key.
▶ To display the current room temperature, press the LED key and hold
for 5 seconds.
▶ To display the set temperature: press and hold the LED key for
another 5 seconds.
3.6.3 Energy saving functions
The following energy saving functions can be selected at the unit:
1)
• ECO : operation with fan speed AUTO and set temperature of at
least 24 °C
• GEAR (75%): reduce power consumption by 25 %
• GEAR (50%): reduce power consumption by 50 %
• None of the above symbols: normal operation
▶ To activate an energy saving function, press
required function is displayed.
The ECO function automatically sets a temperature of 24 °C if the
previously set temperature is lower. The function switches off as soon as
the temperature is lowered to less than 24 °C.
3.6.4 Noise reduction (Silent Mode)
This function reduces the noises emitted by the indoor and outdoor unit
when it is in operation. This is particularly advantageous at night, if you
need to show consideration for your neighbours.
▶ During operation, press the
Exiting the function:
▶ Press the key again for 2 seconds.
-or-
▶ Press the K key, Mode key, Turbo key or Clean key.
When the outdoor unit is in quiet mode, it may not be possible to achieve
the required cooling/heating capacity because the compressor operates
at a low frequency.
3.6.5 Indirect airflow function (Wind avoid me)
This function prevents a direct airflow onto the body.
The function is only available in cooling mode, dehumidification mode
and fan mode.
3.6.6 Turbo cool/Turbo heat
When Turbo cool/Turbo heat is active, the indoor unit operates at
maximum power to heat or cool the room quickly.
▶ Turbo cool: switch on Cooling mode and press the Turbo key.
▶ Turbo heat: switch on heating mode and press the Turbo key.
Exiting the function:
▶ Press the Turbo key again.
1) Only in cooling mode
Climate 3000i – 6721823682 (2021/09)
key until the
key for 2 seconds.
3.6.7 Self-cleaning (I clean)
The unit has a self-cleaning function for the evaporator. The self-cleaning
freezes dust, mould and grease. Everything is then quickly defrosted and
dried with hot air.
▶ To activate the self-cleaning: press the Clean key.
CL appears on the display of the indoor unit when self-cleaning is in
progress. Self-cleaning ends automatically after 20 to 45 minutes.
3.6.8 Frost protection (8 °C Heating)
The frost protection can be activated to keep the room temperature at a
minimum of 8 °C.
▶ In heating mode, press the / key 2x within 1 second.
The unit remains off until the temperature falls below 8 °C.
Exiting the function:
▶ Press the K key, Mode key, Turbo key or Clean key.
3.6.9 Key lock function
The keys of the remote control can be locked with the keylock.
▶ To switch the keylock on/off: press the Clean and Turbo keys
simultaneously for 5 seconds.
The symbol appears in the display when the keylock is active.
3.6.10 Advanced operating functions
▶ Press the Set key.
▶ Press the Set key or ., / keys to select the function.
– = Sleep mode function
– = Follow me function
– = Wireless control function
▶ Confirm selection with the OK key.
Exiting the function:
▶ Repeat the above steps.
Sleep mode
The purpose of this function is to save energy during idle times. After an
hour, the unit heats or cools less intensely. To do this, the set
temperature is changed by 1 °C. After two hours the set temperature
changes by a further 1 °C. The new temperature then remains constant.
The function is not available in dehumidification mode and fan mode.
Follow Me function (Follow Me)
The function activates the remote control at the current location in order
to measure the temperature at 3-minute intervals. The indoor unit is now
controlled with reference to these measurements.
The Follow Me function is only available in cooling mode, heating mode
and automatic mode.
Wireless control function
The purpose of this function is to establish a connection via WLAN. If the
unit is not displaying the function, the LED key must be pressed quickly
seven times in succession instead.
To connect to WLAN an IP-Gateway (accessory) must be installed.
Operation
53