Publicité
Les langues disponibles
Les langues disponibles
RE VERSE
We thank you for your choice of a BEEPER system to protect your vehicle. The
BEEPER systems have been conceived and produced to give you a complete
satisfaction. Our engagement of reliability will offer your car many quiet years,
we guarantee this product during 36 months. We advise you to make install this
system by a professional and to read carefully this manual for a perfect use of
the BEEPER system.
PARTS & FEATURES
Control unit
Control unit
Control unit
Sensor
Sensor
Sensor
Antenna
• Electromagnetic parking sensor
• Fitting perfectly all types of vehicles with a non metallic bumper and less large
than 2,5 m.
• Detection range from 20 to 80 cm
• Easy and quick installation
INSTALLATION
ANTENNA INSIDE THE BUMPER COVER
• The electromagnetic sensor antenna foil must be stuck inside the bumper cover
on a plastic area large enough of 3 cm and a maximal length of 2,5 meters. This
area should be plane and without metallic parts or roughness that could disturb
the good detection of the product.
• For a perfect installation, we advice to remove the bumper cover of the car
body. But if you can place the antenna foil without removing the bumper, you
must check under the car the area where you will stick the antenna foil.
Clean the mounting area you have choosen to get a perfect condition to stick
the antenna foil.
• Find out a hole behind the bumper to lead the antenna foild wire to the car
trunk. If there is no hole, you can drill of hole of 10 mm diameter to lead this
wire and connector.
• A grommet is supplied with the product to insert on the hole.
• Place the antenna foil all along
the interior face of the bumper to
check the best position of the foil.
peel 10 cm of the sticker and stick
it inside the bumper. Do not peel
the whole sticker once, do it step
by by step 10 cm per 10 cm.
• The antenna foil should not be
stuck in the corners of the bumper.
The antenna foil should be stuck as
plane as possible.
• Place the control unit inside the trunk and connect the black wire with on the
antenna foil connector.
• Place the buzzer at the most appropriate place to help driver o hear clearly
the buzzer alert.
• The free wires BLACK & RED should be connected as further :
BLACK : Ground
Connect it on a ground plot of the car
RED : +12 V Reverse light
Buzzer
Buzzer
Buzzer
Find out the original wire that powers
the reversing light. This wire should be
+12V when reverse light is ON and 0V
when reverse light if OFF.
Use the scotch lok connectors to con-
nect the wires (see below)
Place the scoth lok®
connector on the original
wire (reverse light)
Installation is finished, we advice you to test the parking sensor. Turn the vehicle's
ignition key to the ON position but do not start the engine. Place the vehicle's
transmission in reverse gear.
Use a plain object of about 50 cm x 50 cm size. Stand it about 1 m. far from the
bumper and slowly approach the vehicle.
The buzzer will sound fast beep from 80 to 40 cm and continuous beep from
40 to 20 cm.
Cutaway view to show antenna foil position
INSIDE THE TRUNK
WHITE / BLACK wires
to the BUZZER
for sound alert
BLACK wire
to antenna
foil in the bumper cover
BLACK wire : ground
RED wire : +12V reverse light
SCOTCH-LOK ® connectors
Insert the red wire inside the
Use a clamp to close the
second place of the connector
connector and link the 2
wires
TEST & USE
PROGRESSIVE BUZZER SOUND ALERT
From 80 cm to 40 cm
BI BI BI BI
From 40 cm to 20 cm
BIIIIIIIIIIIIIIIII
INSTALLATION ASSISTANCE
For any technical assistance, please contact our technical hot line on monday to friday
from 9 to 12 AM & 2 to 6 PM.
Hot Line
0 892 690 792
0,34 €uros TTC/Min
GUARANTEE
The BEEPER REVERSE devices have a 3-year guarantee (36 months).
We consider the guarantee according the below conditions :
• The guarantee starts the day you buy the BEEPER REVERSE in an official distributor marked
on your invoice. If the system is installed after the date of buying, Only the date of buying
will be considered.
• Without proof of buying (invoice), The guarantee will be from the date of the production
of the device + 36 months.
• The guarantee only works on the products, excluding the installation / removing, technical
intervention or any labour costs.
• The freight charges of the products to our technical department are charged to the buyer,
the return of the products will be charged to IXIT only for France (Excluding Overseas and
foreign countries (IXIT to the buyer)).
• The products and the accessories must not be opened, analysed, modified, repaired... by
other technical departments than IXIT.
• The products and accessories must have a fair wear and tear, no shocks, or any indication
of damaging
• The products and accessories must not have any oxydation or humidity coming from water
splash or a bad protection of the system.
• In case of no trouble of the product, the freight charges from IXIT to the customer will
be charged to the Customer. The labour costs for the testing will be charged to the customer
• An invoice will be edited after a repairment order validated by the customer.
CEM CONFORMITY DECLARATION
Designation :
REM101 U301 BEEPER IXIT
PARKING SENSOR
Manufacturer :
IXIT SAS - LONG-E
Type :
ELECTROMAGNETIC PARKING SENSOR
Declare that the above equipment comply with the essential requirement of the directive CE R10
Electromgnetic compatibility :
EN 55013:2001+A1:2003
EN 55020:2007
Declare that the essential radio tests have been done
The CE marking is printed on the quipment
Date of affixing of the CE marking : 2008
Test report : 377-0001-08-TAES
Date : 13/05/08
Fast bip
Continuous beep
22! rue de l'ancienne distillerie
Parc des grillons
69400 GLEIZE FRANCE
contact@ixit.fr
Publicité
