Before Putting The Machine Into Operation - EINHELL NTS 1725 L Mode D'emploi D'origine

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Anleitung_NTS_1725_L_SPK7:_
GB
Tilting saw blade
Extractor socket
Weight
Laser class
Laser wavelength
Laser output
Laser power supply
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 17/18/29)
Turn the saw upside down and place it on the
floor.
The four legs (40) should be screwed to the
machine so that both legs which have 2 bore-
holes on the underside (40) are facing the rear of
the machine.
Now fasten the longitudinal struts and cross
18
12.07.2010
8:02 Uhr
Seite 18
infinite 0° - 45°
struts (41) as well as the four center struts (42)
loosely to the legs.
Ø 35 mm
Be sure to secure the hex screws and nuts only
33,5 kg
loosely. Important: The longer struts have to be
2
used on the sides.
650 nm
Now mount the rubber feet (43) on the legs and
turn the saw together with the base frame so
≤ 1 mW
that it stands upright on the floor.
2 x 1.5 V (AAA)
Finally, secure all the screws and nuts on the
base frame so that they are tight (Fig. 18).
Screw the additional legs (48) to the rear legs
(40) so that they point towards the rear of the
machine.
7.2 Table width extension and length extension
(Fig. 19/20)
Use the screws and nuts to fasten the table
width extension and length extension (35/36)
loosely to the saw table (1) (Fig. 19).
Screw the supports (27) loosely onto the saw
housing and onto the table width extension or
length extension (short supports for the width
extension, long supports for the length
extension).
Align the table width extension and length
extension level with the saw table (1).
Finally, tighten all screws. (Fig. 20)
7.3 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (44) in the
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.4. Setting the splitter (Fig. 3/6/7/8)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (20).

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.406.4911020

Table des Matières