Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
5. REMOTE CONTROL ADJUSTMENTS - INSTALLER
5. REMOTE CONTROL ADJUSTMENTS - INSTALLER
The remote control allows:
5. REMOTE CONTROL ADJUSTMENTS - INSTALLER
-
Adjust the airflows (1
The remote control allows:
-
Timer for adjusting the filter maintenance period (6, 9, 12 or 15 months) (factory
-
Adjust the airflows (1
The remote control allows:
setting 9 months)
-
Timer for adjusting the filter maintenance period (6, 9, 12 or 15 months) (factory
-
Adjust the airflows (1
-
Adjust the balance of supply / extraction airflows
setting 9 months)
-
Timer for adjusting the filter maintenance period (6, 9, 12 or 15 months) (factory
-
Adjust the balance of supply / extraction airflows
setting 9 months)
5.1 Adjustment of the airflows
-
Adjust the balance of supply / extraction airflows
5.1 Adjustment of the airflows
5.1 Adjustment of the airflows
st
(1
) low speed
adjustment
st
(1
) low speed
adjustment
st
(1
) low speed
5. REMOTE CONTROL ADJUSTMENTS - INSTALLER
adjustment
The remote control allows:
-
Adjust the airflows (1
To adjust the airflow turn the potentiometer carefully clock wise with a small screw driver.
-
Timer for adjusting the filter maintenance period (6, 9, 12 or 15 months) (factory
The potentiometer has 16 positions (from 0 to F). To each of these positions are assigned
To adjust the airflow turn the potentiometer carefully clock wise with a small screw driver.
setting 9 months)
an output voltage to the fans. As higher the output voltage as higher the airflow and
The potentiometer has 16 positions (from 0 to F). To each of these positions are assigned
To adjust the airflow turn the potentiometer carefully clock wise with a small screw driver.
-
Adjust the balance of supply / extraction airflows
viceversa.
an output voltage to the fans. As higher the output voltage as higher the airflow and
The potentiometer has 16 positions (from 0 to F). To each of these positions are assigned
viceversa.
an output voltage to the fans. As higher the output voltage as higher the airflow and
5.1 Adjustment of the airflows
Position Potentiometer
st
Factory setting: 1
speed = 3; 2
viceversa.
Assigned Voltage (V)
st
Factory setting: 1
speed = 3; 2
Adjustment of the filter maintenance period
st
Factory setting: 1
speed = 3; 2
It is possible to set the period to 6, 9, 12 or 15 months (9 months factory setting). The
Adjustment of the filter maintenance period
filter clogging depends on the pollution of the area where the unit is installed. We
It is possible to set the period to 6, 9, 12 or 15 months (9 months factory setting). The
Adjustment of the filter maintenance period
st
(1
) low speed
recommend checking the time in which the filter clogs and adjusting this period. It is
p
filter clogging depends on the pollution of the area where the unit is installed. We
sf
It is possible to set the period to 6, 9, 12 or 15 months (9 months factory setting). The
adjustment
[mmcda]
advisable to do this after the second filter change. Of course, after the installation, the
recommend checking the time in which the filter clogs and adjusting this period. It is
filter clogging depends on the pollution of the area where the unit is installed. We
extract air is dusty and not representative. During the second filter check, if you notice
60
advisable to do this after the second filter change. Of course, after the installation, the
recommend checking the time in which the filter clogs and adjusting this period. It is
that the filters are clean you can increase the time (12 or 15, months), if you notice that the
extract air is dusty and not representative. During the second filter check, if you notice
advisable to do this after the second filter change. Of course, after the installation, the
50
filters are very dirty you should decrease the time (6 months).
that the filters are clean you can increase the time (12 or 15, months), if you notice that the
extract air is dusty and not representative. During the second filter check, if you notice
Open the box and adjust the timing as shown. To do this, set the micro contacts 1 and 2
40
filters are very dirty you should decrease the time (6 months).
that the filters are clean you can increase the time (12 or 15, months), if you notice that the
as shown in the drawings below to adjust the month.
Open the box and adjust the timing as shown. To do this, set the micro contacts 1 and 2
To adjust the airflow turn the potentiometer carefully clock wise with a small screw driver.
30
filters are very dirty you should decrease the time (6 months).
as shown in the drawings below to adjust the month.
The potentiometer has 16 positions (from 0 to F). To each of these positions are assigned
Open the box and adjust the timing as shown. To do this, set the micro contacts 1 and 2
20
an output voltage to the fans. As higher the output voltage as higher the airflow and
as shown in the drawings below to adjust the month.
10
viceversa.
0
st
Factory setting: 1
speed = 3; 2
Adjustment of the filter maintenance period
Filters alarm timing
It is possible to set the period to 6, 9, 12 or 15 months (9 months factory setting). The
Filters alarm timing
filter clogging depends on the pollution of the area where the unit is installed. We
Filters alarm timing
recommend checking the time in which the filter clogs and adjusting this period. It is
advisable to do this after the second filter change. Of course, after the installation, the
extract air is dusty and not representative. During the second filter check, if you notice
that the filters are clean you can increase the time (12 or 15, months), if you notice that the
filters are very dirty you should decrease the time (6 months).
Open the box and adjust the timing as shown. To do this, set the micro contacts 1 and 2
as shown in the drawings below to adjust the month.
st
nd
speed, 2
speed, 3
st
nd
speed, 2
speed, 3
st
nd
speed, 2
speed, 3
st
nd
speed, 2
speed, 3
0
1
2
3
4
nd
speed = 7 and 3
2,5
3
3,5
4
4,5
nd
speed = 7 and 3
nd
speed = 7 and 3
CAD HE 450 EC H BASIC
p
sf
[Pa]
10V
600
500
8V
400
6V
300
200
4V
100
0
0
nd
100
200
300
speed = 7 and 3
rd
speed)
rd
speed)
rd
speed)
rd
(3
) high speed
adjustment
rd
(3
) high speed
adjustment
rd
(3
) high speed
adjustment
nd
(2
) middle speed
adjustment
nd
(2
) middle speed
adjustment
nd
(2
) middle speed
adjustment
rd
speed)
5
6
7
8
9
rd
speed = F.
5
5,5
6
6,5
7
7,5
rd
(3
) high speed
rd
speed = F.
adjustment
rd
speed = F.
nd
(2
) middle speed
adjustment
q
3
rd
400
500
v [m
/h]
speed = F.
A
B
C
D
E
8
8,5
9
9,5
F
10
29
Publicité
Table des Matières
