Rowenta ES440010 Mode D'emploi page 7

IFU_RO_PERFECTO_4400_NC00025894-01_eo 27/09/11 11:26 Page7
• The LED flashes while the machine is warming up,
then remains lit. The appliance is then ready for use.
• Release the filter holder by pressing the
lightly and turning it towards the left
9)
. Using the measuring spoon, place the ground
coffee into the filter holder: one measuring spoon
(filled to the top) per cup for a good espresso
10a)
.
• Remove the excess ground coffee from the edge of
(fig. 10b)
the filter holder
• Insert the filter holder into the appliance tightening it
by turning it towards the right as far as possible
12).
• Place a cup on the grill of the drip tray under the filter
(fig. 13).
holder
• Turn the selector d1 to the position (coffee)
• Press either the d3 button
button for 2 cups.
• After a few moments, the coffee stars to flow.
• When the cups are full, the coffee stops flowing
automatically. Move the selector d1 back to the
(fig. 7)
position
• Remove the cup.
• Release the filter holder: press the
while turning the filter holder towards the left and
remove it from the appliance. Throw away the used
coffee using the ejection system by pressing the
"push" button on the handle fully
filter holder under running water, while pressing the
"push" button to eliminate the remains of ground
coffee (see also paragraph 8.B for deeper cleaning).
It is normal that each time the control selector d1
returns to the position
running water or steam, due to a specific device which
eliminates the pressure from the circuits.
With an E.S.E espresso pod
"ESE" for "Easy Serving Espresso" is a
pod (44 mm in diameter) of 7g of coffee
that has been selected, ground and com-
pacted between two filter papers especially
designed to make Italian style espresso
("ristretto" short coffee).
This system permits easy, simple, clean
and comfortable use of your machine.
• Before removing the removable tank, remember to
place the selector d1 in the position
• Fill the tank with cold water and fit it back onto the
(fig. 8)
appliance .
• Switch on the appliance by pressing the ON/OFF
button d2 .
• The LED flashes during preheating, then remains lit.
The appliance is then ready for use.
button
(fig.
(fig.
.
(fig.
(fig. 4).
for 1 cup or the D4
button lightly
(fig. 16)
. Wash the
there is a low noise of
(fig. 7)
.
7
• Release the filter holder by pressing the
lightly and turning it towards the left
required, remove the paper around the pod
(fig. 11)
following the dotted lines
pod with the red writing facing downwards (fold the
corners of the filter paper back). Ensure that the
paper is placed inside the filter, otherwise this could
cause leaks. For creamier and thicker froth, the E.S.E
pod must be positioned correctly. The pod is
designed to make one cup of coffee. The use of 2
E.S.E pods on top of one another is not
recommended.
• Insert the filter holder into the appliance tightening it
by turning it towards the right as far as possible
12).
• To prepare your espresso, follow the same
procedure as for the preparation of an espresso with
ground coffee.
With a soft pod
Your machine is also compatible with soft
pods (generally 60 mm in diameter).
As this type of pod is not specifically designed
for espresso machines, you will obtain a wea-
ker espresso than with an E.S.E. pod.
• Before removing the removable tank, remember to
place the selector d1 in the position
• Fill the tank with cold water and fit it back onto the
(fig. 8)
appliance .
• Switch on the appliance by pressing the ON/OFF
button d2 .
• The LED flashes during preheating, then remains lit.
The appliance is then ready for use.
• Release the filter holder by pressing the
lightly and turning it towards the left
a soft pod into the filter holder. The pod is designed
to make one cup of coffee. The use of 2 pods on top
of one another is not recommended.
• Insert the filter holder into the appliance tightening it
by turning it towards the right as far as possible
12).
• To prepare your espresso, follow the same
procedure as for the preparation of an espresso with
ground coffee.
7. INDIVIDUAL PROGRAMMING
OF THE VOLUME OF COFFEE:
To change the pre-programmed amount of water,
proceed as follows:
• Fill the water tank and turn the machine on
1 abc, 2, and 4)
.
• Put a spoonful of coffee in the filter by using a
measuring spoon or use an E.S.E. or soft pod.
button
(fig. 15)
. If
EN
. Place the E.S.E
(fig.
(fig. 7)
.
button
(fig. 15)
. Place
(fig.
(fig.