Noise/Vibration Information - Bosch PWS 1000-125 Notice Originale

OBJ_BUCH-1961-008.book Page 20 Friday, May 20, 2016 1:14 PM
20 | English
Angle Grinder
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the
product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and
h
uncertainty K determined according to
EN 60745-2-3:
Surface grinding:
a
h
K
Disk sanding:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
1 609 92A 1ZV | (20.5.16)
PWS ... 1000-125
kg 2.2
kg 2.2
/II
PWS ... 1000-125
3 603 ... CA2 6..
dB(A) 90
dB(A) 100
dB 3
2
m/s 7.0
2
m/s 1.5
2
m/s 5.0
2
m/s 1.5
Protection Guard for Grinding
Adjust the position of the protection guard 7 to the require-
ments of the work process. For this, press the release lever 1
upward and turn the protection guard 7 to the required posi-
tion.
 Always adjust the protection guard 7 in such a manner
that all 3 red cams of release lever 1 engage into the
corresponding notches of the protection guard 7.
 Adjust the protection guard 7 in such a manner that
sparking is prevented in the direction of the operator.
 The protection guard 7 may be turned only upon actua-
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
1000-125 CE 1300-125 CE
2.1 2.4
2.1 2.4
/II /II
1000-125 CE 1300-125 CE
CA2 8.. CA2 9..
90 93
101 104
3
8.0 13.0
1.5 1.5
5.0 6.0
1.5 1.5
Place the protection guard 7 onto
the spindle collar of the machine
until the encoding keys of the pro-
tection guard agree with the spin-
dle collar. Press and hold the re-
lease lever 1 while doing this.
Press the protection guard 7 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Bosch Power Tools
3