Dust/Chip Extraction; Starting Operation - Bosch PWS 1000-125 Notice Originale

OBJ_BUCH-1961-008.book Page 22 Friday, May 20, 2016 1:14 PM
22 | English
A properly attached, undam-
aged quick-clamping nut can
be loosened by hand when
turning the knurled ring in an-
ticlockwise direction.
Never loosen a tight quick-
clamping nut with pliers. Al-
ways use the two-pin span-
ner. Insert the two-pin span-
ner as shown in the
illustration.
Approved Grinding Tools
All grinding tools mentioned in these operating instructions
can be used.
-1
The permissible speed [min ] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Therefore, observe the permissible rotational/circumferen-
tial speed on the label of the grinding tool.
max.
[mm] [mm]
D b
d
125 6 22.2
D
b
D
125 –
d
75 30 M 14
b
D
Rotating the Machine Head
 Before any work on the machine itself, pull the mains
plug.
Completely unscrew the four screws. Rotate the machine
head carefully, without removing it from the housing, to the
new position. Screw in and tighten the four screws again.
1 609 92A 1ZV | (20.5.16)

Dust/Chip Extraction

 Dust from materials such as lead-containing coatings,
 Prevent dust accumulation at the workplace. Dust can
Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-
-1
d [min ] [m/s]
11000 80
When operating the machine with power from mobile genera-
tors that do not have sufficient reserve capacity or are not
equipped with suitable voltage control with starting current
amplification, loss of performance or untypical behavior can
– 11000 80
occur upon switching on.
Please observe the suitability of the power generator being
used, particularly with regard to the mains voltage and fre-
quency.
11000 45
Switching On and Off
PWS 1000.. (see figure A)
To start the power tool, push the On/Off switch 3 forwards.
To switch off the machine, release the On/Off switch 3.
PWS 1300.. (see figure B)
The machine head can be
To start the power tool, press the On/Off switch 3 forward
rotated with respect to
and then down.
the machine housing in
To lock the On/Off switch 3, press the On/Off switch 3 down
90° steps. In this man-
at the front until it latches.
ner, the On/Off switch
To switch off the power tool, release the On/Off switch 3 or,
can be brought into a
if it is locked, briefly push down the back of the On/Off switch
more convenient posi-
3 and then release it.
tion for special working
To save energy, only switch the power tool on when using it.
situations, e. g., for cut-
 Check grinding tools before using. The grinding tool
ting operations using the
cutting guide with dust
extraction protection
guard 19 or for left-
handed persons.
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
easily ignite.
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools. Damaged grinding tools can burst and cause in-
juries.
Bosch Power Tools