Publicité
Les langues disponibles
Les langues disponibles
Adjust the height of the laser so the center of the
5.
beam is aligned with
Directly above or below
6.
laser beam (Figure
D 3
Measure the vertical distance between
7.
.
c
If your measurement is greater than the
8.
Allowable Distance Between
corresponding Distance Between
the following table, the laser must be serviced at
an authorized service center.
Distance Between
and
a
b
30' (9m)
40' (12m)
50' (15m)
Horizontal Beam - Pitch Direction
Checking the horizontal pitch calibration of the
laser requires a single wall at least 30' (9m) long.
It is important to conduct a calibration check using
a distance no shorter than the distance of the
applications for which the tool will be used.
Place the laser against the end of the wall (Figure
1.
).
E 1
Move the Power/Transport Lock switch to the
2.
right (Figure
) to turn the laser ON in self-
A 3
leveling mode and display a horizontal laser beam.
At least 30' (9m) apart along the laser beam,
3.
mark
and
a
.
b
Move the laser to the opposite end of the wall
4.
(Figure
).
E 2
Position the laser toward the first end of the same
5.
wall and parallel to the adjacent wall.
Adjust the height of the laser so the center of the
6.
beam is aligned with
Directly above or below
7.
laser beam (Figure
Measure the distance between
8.
(Figure
).
a
D 2
, mark
along the
b
c
).
and
b
and
for the
b
c
and
a
b
Allowable Distance
Between
and
b
5/32" (4mm)
7/32" (6mm)
5/16" (8mm)
.
b
, mark
along the
a
c
).
E 3
and
.
a
c
If your measurement is greater than the
9.
Allowable Distance Between
corresponding Distance Between
the following table, the laser must be serviced at
an authorized service center.
Distance Between
and
a
30' (9m)
40' (12m)
in
50' (15m)
Vertical Beam - Plumb
Checking the vertical (plumb) calibration of the
c
laser can be most accurately done when there is
a substantial amount of vertical height available,
ideally 30' (9m), with one person on the floor
positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to
conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
Place the laser at least 3.28 ft (1.0m) from a door
1.
jamb (Figure
Move the Power/Transport Lock switch to the
2.
right (Figure
leveling mode and display a horizontal laser beam.
Press
once to display the vertical beam.
3.
Aim the vertical laser beam toward the door jamb.
4.
Along the bottom of the laser beam, mark three
5.
locations
a
between
a
6.
Where the top of the laser beam appears at the
top of the door jamb, mark
7.
Move the laser to the opposite side of the door
jamb (Figure
Align the bottom of the laser beam with
8.
and
.
c
9.
Where the top of the laser beam appears at the
top of the door jamb, mark
Measure the distance between
10.
and
a
a
Allowable Distance
Between
b
a
5/32" (4mm)
7/32" (6mm)
5/16" (8mm)
).
F 1
) to turn the laser ON in self-
A 3
; where
,
, and
b
c
b
and
.
c
.
e
).
F 2
.
f
and
e
GB
for the
c
and
in
b
and
c
is midway
,
,
a
b
.
f
11
Publicité
